Hatco THERMO-FINISHER TFWM Series Скачать руководство пользователя страница 11

Form No. TFWMM-0817

11

English

OPERATION

Food Finisher Operation

The quick heating, infrared ribbon heating element(s) in each 

heating bay are activated by the placement of a plate or tray 

on the adjustable shelf. The weight of the plate/tray causes 

the adjustable shelf to swing down and back slightly, which 

activates a switch. The plate/tray must weigh approximately 1 

lb. (0.5 kg) to activate the heating element. The switch signals 

the ribbon heating element(s) to begin heating. Removing the 

plate/tray from the adjustable shelf deactivates the switch and 

signals the ribbon heating elements to return to stand-by mode.
  • When a plate/tray is placed on an adjustable shelf, the 

POWER ON indicator light for the corresponding heating 

bay will illuminate (heating mode). When the plate/tray is 

removed, the indicator light will shut off (stand-by mode).

  • The bay dividers in between each heating bay are 

removable to allow the use of a larger tray across two 

adjustable shelves (make sure shelves are at the same 

height).

WARNING

BURN HAZARD: Turn power switch OFF (O), unplug power 

cord/turn off power at circuit breaker, and allow unit to 

cool before performing any maintenance, cleaning, or 

adjustments.

  • The TOP HEAT CONTROL knobs and BOTTOM HEAT 

CONTROL knobs (TFWM42-3939 and TFWM36-3939 

only) provide a wide range of adjustment to the heat 

intensity of the ribbon heating elements. Test different food 

products in the unit to determine the best settings for each.

Weight of plate on adjustable

shelf activates ribbon heating

elements.

Adjustable

Shelf

Removable

Divider

Operating the Food Finisher

Shutdown

  1.  Wait for fifteen minutes after the last operation of the food 

finisher.

  2. Move the POWER ON/OFF (I/O) switch to the OFF (O) 

position.

 

• All power to the unit is off and automatic plate/tray 

activation is disabled.

 

• The cooling fans on 3600 and 3636 models will continue 

running until unit is cooled.

POWER ON/OFF

(I/O) Switch

BOTTOM HEAT

CONTROL Knob

TOP HEAT

CONTROL Knob

POWER ON

Indicator Light

Left Heating 

Bay Controls

Center Heating 

Bay Controls

Right Heating 

Bay Controls

High Limit

Indicator

Light

Control Panel (TFWM36-3939 shown)

Содержание THERMO-FINISHER TFWM Series





























Отзывы: