Harmonic PWRLink II 4800T Series Скачать руководство пользователя страница 37

Страница: 37 / 43

Technical Specifications

PWRLink II 4800T Optical Transmitter Product Manual Rev A (2/02)

A–3

A.4 User

Interface

Front panel

Bi-state status LED: Normal = Green, Alarm = Red

Module selection indicator: Yellow LED

RF attenuation adjustment

Monitor point:

Monitor port to RF input: -20 dB

Flatness: ±1.0 dB

Return loss: >16 dB

Connector type: Female F

Rear panel

RF input connector type: Female F

Optical output (for connector types available, see Section A.8)

Element Management System—NETWatch Site Controller

Interface: RS-485, RS-232C connectors (in HLP 4200)

Carrier: Externally generated

A.5 Power

Requirements

Nominal: +24 VDC; supplied by HLP 4200 bus

Maximum: +28 VDC

Consumption: 22 Watts maximum

A.6 Environmental

Operating temperature

: 0

to +50

C (+32

to +122

Storage temperature: -40

to +70

C (-40

to +158

Automatic fan adjustment at: 40

& 50

C (104

& 122

Relative humidity: 85% non-condensing

Over temperature laser protection: Software and hardware

For operation over entire temperature range, subtract 2 dB from CSO and CTB worst-case
performance specifications.

Содержание PWRLink II 4800T Series







































Результаты поиска

Содержание PWRLink II 4800T Series

Отзывы:

Harmonic PWRLink II 4800T Series, Руководство по эксплуатации продукта, Страница: 37 / 43

Результаты поиска

Содержание PWRLink II 4800T Series

Отзывы: