manualshive.com logo in svg

Harman Martin Exterior 400 Series, Руководство пользователя

Поделиться
Скачать
Harman Martin Exterior 400 Series Скачать руководство пользователя страница 29

Service and maintenance

 29

Software installation

It may be necessary to upload new software (i.e. firmware) to an Exterior 400 Range fixture if you believe 
that the product has a software-related fault or if you want to update to a newer version. Software updates 
are available from the Martin website (http://www.martin.com) and can be installed via the DMX data link 
with the following items: 

• The Martin Uploader application, version 5.0 or later, downloadable free of charge from the Support area 

of the Martin website. 

• The fixture’s main CPU software update file, downloadable free of charge from the Support area of the 

Martin website (this file can be downloaded automatically from within the Martin Uploader application)

• A Martin Universal USB-DMX Interface or similar PC/fixture hardware interface and a Windows PC (if you 

have a Martin MP-2 Uploader device, it can also be used). 

Installing software: normal method

1. Connect the uploader hardware to a Exterior 400 Range fixture’s data input connector. The software will 

be uploaded to that fixture and all fixtures of the same type that are powered on and connected via the 
DMX link.

2. Upload the fixture software as described in the uploader’s help file or user documentation.

3. Disconnect the uploader hardware and reconnect the fixture to the DMX link.

4. Cycle power off and on. Check that the fixture resets correctly. If an error message appears in the 

display, cycle power off and on again and check that the fixture now resets correctly.

Installing software: boot mode upload

A boot mode upload may be required if the 
software update notes call for it or if the 
fixture software is seriously corrupted and 
the fixture will not accept a software upload 
using the normal method described above.

To carry out a boot mode upload:

1. Isolate the fixture from power and allow 

to cool for at least 20 minutes.

2. Open the rear cover (see Figure 8 on 

page 13).

3. Locate the DIP switch on the main PCB 

and move pin 6 to OFF.

4. Reinstall the rear cover seal and the rear cover temporarily.

5. Reapply power and perform the upload as described above.

6. Isolate from power, open the rear cover and move DIP pin 6 back to ON. 

7. Reinstall the rear cover as follows:

a. Check that the seal is in perfect condition.

b. Place the seal and cover in position and drive the cover screws until they are finger-tight only.

c. Cross-tighten the screws evenly in a diagonal pattern, increasing torque gradually in stages to a 

maximum torque of 8 Nm (5.9 ft.-lbs.).

8. Reapply power.

9. Check that the fixture resets correctly. If an error occurs, cycle power off and on again and check that the 

fixture now resets correctly.

1 2 3 4 5 6

DIP switch setting for boot 

mode upload

O N

Normal DIP switch setting

1 2 3 4 5 6

O N

Details corrected in manual Rev. D

Содержание Martin Exterior 400 Series









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды