Harman Accentra Скачать руководство пользователя страница 2

Страница: 2 / 32

Harman® • Accentra Owner’s Manual_R40 • 2002 -___ • 11/15

3-90-08326c

Listing Label Information/Location

The model information regarding your specific stove can be found on the rating plate usually located in the control area of

the stove.

A. Congratulations

Congratulations on selecting a Harman® Freestanding Pellet

Stove. The Harman® Accentra pellet stove you have selected

is designed to provide the utmost in safety, reliability, and

efficiency.
As the owner of a new pellet stove, you’ll want to read and

carefully follow all of the instructions contained in this owner’s

manual. Pay special attention to all cautions and warnings.

Read this manual before operating this appliance.

Please retain this Owner’s Manual for future reference.

Read the Installation Manual before making any installation or finishing changes.

Welcome

Brand:

________________________________________________

Model Name:

___________________________

Serial Number:

__________________________________________

Date Installed:

__________________________

Appliance Information:

Local Dealer Information

DEALER:

Fill in

your name, address,

phone and email

information here and

appliance information

below.

Dealer Name: ________________________________________________________

Address: ____________________________________________________________

____________________________________________________________

Phone: _____________________________________________________________

Email: _____________________________________________________________

Report #/Rapport #

135-S-10b-2

Test to/testé à:

ASTM E 2779-10, ASTEM E 2515-11, ASTM E 1509-04,

ULC/ORD-C1482-M1990, ULC-S627-00, EPA Method 28R
Room Heater Pellet fuel Burning type (UM) 84-HUD

“PREVENT HOUSE FIRES”

Install and Use only in accordance with

manufacture’s installation and operation instructions.
This wood heater needs periodic inspection and repair for proper operation.

Consult the owner’s manual for further information. It is against federal

regulations to operate this wood heater in a manner inconsistent with the

operating instructions in the owner’s manual.

Contact local building or fire officials about restrictions and inspection in your

area.

WARNING: FOR MANUFACTURED HOMES:

Do not install appliance in

a sleeping room. An outside combustion air inlet must be provided. The

structural integrity of the manufactured home floor, ceiling and walls must

be maintained.
Refer to manufacturer’s instructions and local codes for precautions required

for passing chimney through a combustible wall or ceiling. Inspect and clean

exhaust venting system frequently in accordance with manufacturer’s

instructions.
Use a 3” or 4” diameter type “L” or “PL” venting system.

Do not connect this unit to a chimney flue servicing another appliance.

FOR USE WITH PELLETIZED WOOD FUEL ONLY.

Input Rating Max: 5.7 lb. fuel/hr

EPA Certified Emissions: 0.61 g/hr

Electrical Rating: 240 VAC, 50 Hz, Start 2.6 AMPS, Run 2.0 AMPS
U.S. Electrical Rating: 115 VAC, 60 Hz, Start 4.2 AMPS, Run 3.6 AMPS
Fuel Type: Wood Pellets

Route power cord away from unit.
OPERATE ONLY WITH DOORS CLOSED
DANGER:

Risk of Electrical Shock. Disconnect Power Before Servicing Unit.

For Further Instruction refer to Installation and Owner’s Manual.
Replace glass only with 5mm mirrored ceramic available from your dealer.

DO NOT REMOVE THIS LABEL / NE PAS ENLEVER CETTE ÉTIQUETTE

6.25"

USA

CANADA

loor

protector

54"

2.25"

14.75"

24"

Test pour / tested à:

ASTM E 2779-10, ASTEM E 2515-11, ASTM E 1509 à

1504, ULC / ORD-C1482-M1990, ULC-S627-00, EPA Method 28R
L’appareil de chauffage à pellets type de combustion de carburant (UM)

84-HUD

“Empêcher MAISON incendies”

installer et utiliser uniquement en

conformité avec installation et d’utilisation les instructions du fabricant.
Ce poêle à bois doit inspection périodique et la réparation pour un

fonctionnement correct. Consultez le manuel du propriétaire pour plus

d’informations. Ce est contre les règlements fédéraux pour faire fonctionner

ce poêle à bois d’une manière incompatible avec les instructions d’utilisation

dans le manuel du propriétaire.
Contactez le service des incendies à propos des restrictions et l’inspection

dans votre région.

AVERTISSEMENT: POUR maisons préfabriquées:

Ne pas installer

l’appareil dans une chambre à coucher. Une entrée d’air de combustion

à l’extérieur doit être fournie. L’intégrité structurale de la maison étage,

plafond et murs fabriqués doit être maintenue.
Reportez-vous aux instructions du fabricant et les codes locaux pour les

précautions nécessaires pour faire passer la cheminée à travers un mur

ou un plafond combustible. Inspectez et nettoyez système d’évacuation

souvent en conformité avec les instructions du fabricant.
Utilisez un “ou 4” Type de diamètre «L» 3 ou le système de ventilation “PL”.
Ne pas connecter cet appareil à un conduit de cheminée desservant un

autre appareil.

À UTILISER AVEC LA GRANULE DE BOIS SEULEMENT.

Entrée Max Note: £ 5,7 carburant / h

Émissions certifiés EPA: 0,61 g / h

Note électrique: 240 VAC, 50 Hz, 2,6 AMPS Lancer, Exécuter 2,0 AMPS
US Note électrique: 115 VAC, 60 Hz, Start 4,2 AMPS, Run 3,6 AMPS
Type de carburant: granulés de bois

Route cordon électrique de l’appareil.
Fonctionner uniquement avec les portes fermées
DANGER: Risque de choc électrique. Débranchez l’alimentation

avant l’Unité des services.

Pour de plus amples instructions reportez-vous à Installation et le

manuel du propriétaire.
Remplacer le verre seulement avec 5mm miroir en céramique

disponibles chez votre revendeur.

BARCODE LABEL

008

Serial No.

de série:

Rev F

3-90-247

12"

2.25"

352 Mountain House Road

Halifax, PA 17032

ECO:  77540
PARt # / REv:  3-90-247_Rev F
ORiginAtOR:  Spidlet
DAtE:  04/15
LAbEL SizE:  5.25” H x 11.5” W
LOCAtiOn:

Hopper - Rear

CLASS:
ADHESivE: 486
MAtERiAL: MEtAL
ink: bLACk
OvERCOAt:

LAbEL tiCkEt

Corners .062

MODEL / MODÈLE: “Accentra-2”

Room Heater Pellet Fuel-Burning Type

SUITABLE FOR MOBILE-HOME INSTALLATION

This pellet burning appliance has been tested and listed for use in

Manufactured Homes In accordance with OAR 814-23-900 through 814-23-909

Date of Manufacture / Date de fabrication:

2015 2016 2017 JAN FEB MAR APR MAY JUN JUL AUG SEP OCT NOV DEC

Manufactured by / Fabriqué par: Hearth and Home Technologies 352 Mountain House Road, Halifax PA 17032

Made in U.S.A. of US and imported parts. / Fabriqué aux

États-Unis-d’Amérique par des pièces d’origine américaine

et pièces importées.

US ENVIRONMENTAL PROTECTION AGENCY

Certified to comply with 2015 particulate emission standards. Not

approved for sale after May 15, 2020.
Certifié conforme aux normes 2015 d’émission de particules. Non

approuvé pour la vente après le 15 mai 2020.

MINIMUM CEARANCES TO COMBUSTIBLES/

DISTANCE DE SECURITE PAR RAPPORT AUX

MATERIAUX COMBUSTIBLES:

Back Wall / Entre Mur Arrière 2.25”

(25mm)

Side Wall / Entre Paroi Latérale 12"

(305mm)

Corner Installation / En Angle

Walls to Appliance

6.25”

(159mm)

Entre Murs et Appareil

Floor Protection/Protection du Plancher

USA

CANADA

Sides*/Côtés (A)

6”

200mm

Back/Arrière (B)

0”

200mm

Front*/Avant (C)

6”

460mm

*Measured From Glass in the USA ONLY

*Mesurer à partir de la surface de la porte en verre

Use a non-combustible floor protector extending

under and to the sides, front and back of the unit

as shown in floor protection diagram. Measure front

distance from the surface of the glass door.

Recommended:

Non-combustible floor protection

extended beneath the fluepipe when installed with

horizontal venting.

Alcove Installation

Min. Alcove Height

60”

1524mm

Min. Alcove Side Wall

14.75”

375mm

Max. Alcove Depth

24”

610mm

Serial Number

Model Name

This owner’s manual

should be retained for future reference.

We suggest that you keep it with your other important

documents and product manuals.
Your new Harman® Accentra Pellet Stove will give you years

of durable use and trouble-free enjoyment. Welcome to the

Harman® family!

Содержание Accentra

































Результаты поиска

Содержание Accentra

Отзывы:

Похожие инструкции для Accentra

Бренды по названию

Популярные бренды

Harman Accentra, Руководство пользователя

Результаты поиска

Содержание Accentra

Отзывы:

Похожие инструкции для Accentra

Бренды по названию

Популярные бренды