Harman Accentra Скачать руководство пользователя страница 4

Страница: 4 / 32

Harman® • Accentra Owner’s Manual_R40 • 2002 -___ • 11/15

3-90-08326c

Product Specific and Important Safety Information

A. Appliance Certification

B. Mobile Home Approved

This appliance is approved for mobile home installations

when not installed in a sleeping room and when an outside

combustion air inlet is provided.
The structural integrity of the mobile home floor, ceiling, and

walls must be maintained. The appliance must be properly

grounded to the frame of the mobile home and use only listed

pellet vent, Class “PL” connector pipe.
A Harman® Outside Air Kit must be installed in a mobile

home installation.

NOTE:

This installation must conform with local codes.

In the absence of local codes you must comply with

the

ASTM E1509-2004, ULC S628-93, ULC/ORD-C-

1482-M1990, (UM) 84-HUD

THE STRUCTURAL INTEGRITY OF THE

MANUFACTURED HOME FLOOR, WALL, AND

CEILING/ROOF MUST BE MAINTAINED.

DO NOT INSTALL IN SLEEPING ROOM.

WARNING

The Accentra is Certified to comply with

2015 particulate emission standards. Not

approved for sale after May 15, 2020.

MODEL:

Accentra Pellet Stove

LABORATORY:

OMNI Test Laboratories, Inc

REPORT NO.

135-S-10b-2

TYPE:

Pellet Fueled/Supplementary For

Residential Use

STANDARD(s):

ASTM E 1509-04, ULC/ORD-

C1482-M1990, ULC-S627-00,

ASTM E 2779-10, ASTM E 2515-11

ELECTRICAL

RATING

115 VAC, 60 Hz, Start 4.2 AMPS,

Run 3.6 AMPS

GLASS

SPECIFICATIONS

5mm Ceramic Glass

Содержание Accentra

































Результаты поиска

Содержание Accentra

Отзывы:

Похожие инструкции для Accentra

Бренды по названию

Популярные бренды

Harman Accentra, Руководство пользователя

Результаты поиска

Содержание Accentra

Отзывы:

Похожие инструкции для Accentra

Бренды по названию

Популярные бренды