background image

Harman®  •  Accentra Owner’s Manual_R40  •  2002 -___  •  11/15

21

3-90-08326c

Reference Material 

 

A. Safety Reminders

When  operating  your  Harman® Accentra  Pellet  Stove, 

respect  basic  safety  standards.  Read  these  instructions 

carefully before you attempt to operate the Accentra Pellet 

Stove. Failure to do so may result in damage to property or 

personal injury and may void the product warranty.

CAUTION: This appliance must be vented to the outside.

Due to high temperatures, this stove should be placed out 

of traffic and away from furniture and draperies.
Children and adults should be alerted to the hazards of high 

surface temperatures and should stay away  to avoid burn 

to skin and/or clothing.
Young children should be carefully supervised when they 

are in  the same room as the stove.
Clothing and other flammable materials should not be placed 

on or near this stove.
Installation  and  repair  of  this  stove  should  be  done  by  a 

qualified service person. The appliance should be inspected 

before use and at least annually by a qualified service person. 

More  frequent  cleaning  will  be  required.  It  is  imperative 

that  control  compartments,  burners,  and  circulating  air 

passageways of this stove be kept clean.

Disposal of ashes

: Ashes  should  be  placed  in  a  metal 

container  with  a  tight  fitting  lid. The  closed  container  of 

ashes should be placed on a non-combustible floor or on the 

ground, well away from all combustible materials, pending 

final disposal. If the ashes are disposed of by burial in soil 

or otherwise locally dispersed, they should be retained in 

the closed container until all cinders have thoroughly cooled.

Soot and fly ash: 

Formation and need for removal. The 

products of combustion contain small particles of fly ash. 

The fly ash will collect in the exhaust venting system and will 

restrict the flow of the flue gases. Pellet fuels have different 

ash contents depending on what type of wood has been used 

to make the pellets. 

We recommend to clean the system 

after approximately 1 ton of pellets have been burned 

and judge from that how often the stove should be 

cleaned, remember if you change pellets it may change 

how often you have to clean your stove. 

When burning wood slowly, the potential exists for creosote 

to form. The venting system should be inspected periodically 

throughout the heating season to determine if a creosote 

buildup  has  occurred.  If  a  significant  layer  of  creosote 

has accumulated (3mm or more), it should be removed to 

reduce the risk of a chimney fire. If a fire occurs, call the 

fire  department,  shut  down  the  stove,  and  evacuate  the 

residence.  Before  using  the  appliance,  have  the  venting 

system  thoroughly  inspected  and  replace  any  damaged 

components.

USE OF IMPROPER FUELS, FIRE STARTERS OR 

ALTERING THE STOVE FOR HIGHER HEAT OUTPUT 

MAY CAUSE DAMAGE TO THE STOVE AND COULD 

RESULT IN A HOUSE FIRE. USE ONLY APPROVED 

FUELS AND OPERATION GUIDELINES

WARNING

!

KEEP COMBUSTIBLE MATERIALS SUCH AS GRASS, 

LEAVES, ETC. AT LEAST 3 FEET AWAY FROM THE 

POINT DIRECTLY UNDER THE VENT TERMINATION.

WARNING

!

THE STOVE IS HOT WHILE IN OPERATION.
KEEP CHILDREN, CLOTHING AND FURNITURE AWAY.  

CONTACT MAY CAUSE SKIN BURNS.

CAUTION

!

THE STRUCTURAL INTEGRITY OF THE MOBILE 

HOME FLOOR, WALL, AND CEILING/ROOF MUST BE 

MAINTAINED.

CAUTION

!

MOBILE/MANUFACTURED HOME GUIDELINES DO 

NOT ALLOW INSTALLATION IN A SLEEPING ROOM.

WARNING

!

With any hearth appliance, installation of smoke detectors 

is recommended on every level of the home. 

Possible causes of smoke detector activation:

Paint curing process - Open a window near the appliance 

for the first few hours of burning.
Exhaust being drawn back inside the dwelling - Outside air 

connection to the appliance is necessary.
Vent leakage - All interior seams and joints should be sealed 

with silicone where applicable. Follow vent manufacturers 

instructions for proper sealing.

Содержание Accentra

































Отзывы: