20
SYSTEM SETUP
System Setup
the AUX input is highlighted in dark blue. Press
the
Enter Button
6
to confirm. Next proceed
to the SET-UP menu, and move the cursor to the
Audio Adjustments line. Press the
Enter Button
6
to confirm. Next, press the
M
/
N
Navigation
Buttons
9
to move the on-screen cursor to
the
EZSET/EQ SETUP
menu line. Press
the
Enter Button
6
to move to the next
screen.
Figure 6a
Step 5:
The first two screens of the EzSet/EQ
system will now appear to remind you to connect
all the loudspeakers and to plug in the micro-
phone. If you have not already done so, connect
all loudspeakers and plug the microphone into
the
Headphone Jack
4
as described in steps
2 and 3. When you are ready to proceed, make
certain that the cursor is pointing to
NEXT
and
press the
Enter Button
6
. If you do not wish
to continue with the EzSet/EQ process, press the
‹
/
›
Navigation Buttons
9
to highlight
BACK
and then press the
ENTER Button
6
to return to the
MASTER MENU
. Note that if
you attempt to move to the next menu without
plugging in the microphone, a reminder message
will flash at the bottom of the screen.
Figure 6b
IMPORTANT NOTE:
Anyone with hearing that is
sensitive to loud noises should leave the room at
this point, or use ear protection sufficient to
reduce the noise level. Inexpensive foam-style ear
plugs, available at most drug stores, may be used
to reduce the sound level to a tolerable level. If
you are uncomfortable with, or cannot tolerate,
loud sounds and do not use some sort of ear
protection, we strongly recommend that you
leave the room and ask someone else to run the
EzSet/EQ process, or that you do not use
EzSet/EQ and enter the configuration settings
manually, as described on page 21.
Figure 6c
Step 6.
At this point you will begin to hear a
series of test tones circulate among all the
speakers in your system. While this is happening,
the HS 350 is reading the signal to determine
which speaker positions are active, what type of
speaker is present at each active position, what
the distance is from the listening position to each
speaker, and to begin to build a profile of the
impact of the room’s acoustics on the quality of
audio reproduction. When the test is completed
you will hear the tones stop, and the system will
pause for as long as a minute while the proces-
sor makes its calculations. Do not be alarmed if
the “WARNING” message remains on the screen
after tones stop until a results message is dis-
played as shown in Step 6 or 7, below.
NOTE:
While these tests detect whether a speak-
er is connected to a particular output, they can-
not determine whether the speaker is in the cor-
rect position. (For example, it can tell whether a
speaker is connected to the Surround Right out-
put, but it cannot tell whether the speaker is on
the right or left side of your listening room.) For
that reason, we strongly recommend that you try
to listen as the tone circulates, around you,
starting at the left front, right front, center, and
finishing at the left surround and right surround.
If a tone is heard from a speaker position that
does not match this order, make a note of the
incorrect speaker connections. When the test
process stops you will see a message indicating
the Far Field measurements are complete, but
since there is a connection error press the
¤
Navigation Button
9
so that the on-screen
cursor in Fig. 7 is pointing to
BACK
and press
the
ENTER Button
6
. At this point, exit all
menus and turn the receiver off. Check all speak-
er wire connections and then rerun EzSet/EQ.
Step 7.
When the Far Field tests are complete a
message screen will appear to confirm if the pro-
cedure was successful or not. In most cases there
will not be any problems and you will see the
message shown in Figure 6d on your screen. If
the speaker positions shown match the actual
speaker layout in your system select
NEXT
and,
press the
ENTER Button
6
to complete
EzSet/EQ by performing the Near Field
Measurements from the front left, center, front
right and surround left and right speakers. By
taking this separate set of measurements, the
HS 350 is able to complete its view of the room’s
sonic signature and apply equalization as needed
to correct spikes and dips in the system’s
response. Continue these instructions with
Step 8.
Figure 6d
Step 7a.
If the measurements are not successful
due to a missing or malfunctioning speaker, the
message will appear as shown in Figure 6e.
EzSet/EQ is programmed to look for speaker pairs
at the front left/front right, surround
left/surround right and surround back
left/surround back right positions. If the test
results indicate that one, but not both of the
speakers in any of these pairs is present, the
menu will show
NO
next to the speaker position
where the tests did not report back that a speak-
er is present. Should this message appear, make
note of the suspect speaker location, exit all
menus and turn the receiver off. Check all speak-
er wire connections and then rerun EzSet/EQ
until all speakers are detected successfully.
Figure 6e
Step 8.
When the Far Field measurements are
completed, the system will ask you to take Near
Field measurements, one at each five speaker
position. These measurements enable EzSet/EQ
to produce the most accurate settings for both
high and low frequency equalization. The Near
Field measurements are similar to the Far Field
tests, except that the system will “listen” to only
one speaker at a time, rather than sending the
test signals to all speakers in rotation.
Figure 6f
Step 9.
During the Near Field testing, (Figure
6f), you will see an instruction to place the
microphone in a different position than the one
used for the initial Far Field measurements. This
0096CSK - HK HS 350 OM ENG.qxp:34252_HS350_Eng 20/01/09 10:38 Side 20
