DIGITAL AUDIO CONNECTIONS
16
DIGITAL AUDIO CONNECTIONS
Optical Digital Audio Connection Notes
• Remove the dust protection cap from the optical
digital audio output and connect the cable firmly so
that the configurations of both the cable and the
connector match.
• Keep the dust protection cap and always reuse the
cap when not using the connector.
Audio Output From the Unit’s Optical/
Coaxial Digital Audio Output Connector
Disc:
Sound recording
Optical/coaxial digital
format:
audio output:
DVD
Dolby Digital
Dolby Digital bitstream
(2-5.1ch) or PCM
(2ch, 48kHz, 16-bit)
††
Linear PCM
Linear PCM (2ch)
(48/96kHz,
(48/96kHz,
16/20/24-bit)
16/20/24-bit)
DTS
Bitstream or no
output
††
CD
Linear PCM
Linear PCM
(44.1kHz sampling)
††
Digital format must be selected as “Original” or
“PCM” in Digital Output menu (see “Digital Output”
section on page 19).
For Your Reference:
• Dolby Digital is a digital sound compression
technique developed by the Dolby Laboratories
Licensing Corporation. Supporting 5.1- or 7.1-
channel surround sound depending on the specific
disc, as well as stereo (2-channel) sound, this tech-
nique enables a large quantity of sound data to be
efficiently recorded on a disc.
• DTS is another digital audio technology developed
by Digital Theater Systems, Inc. It supports 5.1 and
6.1 surround sound, depending on the specific disc,
thanks to a sophisticated encoding system.
• Linear PCM is a signal recording format used in
CDs. While CDs are recorded in 44.1kHz/16-bit,
DVDs are recorded in 48kHz/16-bit up to
96kHz/24-bit.
• If you have a Dolby Pro Logic Surround decoder
connected to the DVD 31’s analog audio out con-
nectors, thanks to the “Downmix” function of the
DVD 31 you will obtain the full benefit of Pro Logic
from the same DVD movies that provide full 5.1-
channel Dolby Digital soundtracks, as well as from
titles encoded with Dolby Surround.
• The DVD 31 is designed to digitally output 96kHz
PCM audio with a 96kHz sampling rate. However,
some 96kHz DVDs may include copy protection
codes that do not permit digital output. For full
96kHz fidelity from these discs, use the analog
outputs of the DVD 31. If your surround processor
converter does not support 96kHz PCM audio, you
must use the DVD 31 analog outputs for full 96kHz
fidelity with these discs.
• When connecting a receiver or surround processor
with a digital input but which does not contain a
Dolby Digital or DTS decoder, be sure to select
PCM as the initial setting in the Digital Output menu
(see page 19). Otherwise, any attempt to play
DVDs may cause such a high level of noise
that it may be harmful to your ears and damage
your speakers.
• CDs can be played as they would in a conventional
CD player.
Dolby Digital and DTS
Both Dolby Digital and DTS are audio formats used to
record 5.1-channel audio signals onto the digital track
of film. Both of these formats provide six separate
channels: left, right, center, left rear, right rear, and
common subwoofer.
Remember that Dolby Digital or DTS will only play
5.1-channel sound if the optical or coaxial output of
the DVD 31 is connected to a DTS or Dolby Digital
receiver or decoder (see page 13) and if the disc was
recorded in the Dolby Digital or DTS format.
NOTE:
Some first-generation DTS decoders that do
not support DVD-DTS interface may not work properly
with the DVD/CD player.
DVD-Audio
The high-resolution output of DVD-Audio discs is only
available as an analog signal, due to a combination of
technical limitations on current digital output devices
and various copy protection requirements. For that rea-
son, it is necessary to make direct analog connections
between the
5.1-Channel Direct Outputs
¢
on the
DVD 31 and the matching 5.1 direct inputs on your
A/V receiver or surround processor.
DVD 31 (120V) OM 6/25/04 11:40 AM Page 16