©2009 Yamaha Corporation All rights reserved.
Printed in China WR96010-1
MCX-RC100 / MCX-A300 / MCX-P200
GETTING STARTED
This guide explains the basic way to build a WiFi network between
your MusicCAST2 products and WiFi router and enjoy digital music
distribution via the WiFi network.
Complete description of MusicCAST2 products is available on our
website. To access the MusicCAST2 website, please enter the following
URL on your browser.
MusicCAST2 website:
www.yamaha.com/musiccast
Network to build in this guide
MASTER
PURE DIRECT
VOLUME
MAIN ZONE
INPUT
OFF
ON
INFO
ZONE ON/OFF
ZONE CONTROLS
MULTI ZONE
MIC
OPTIMIZER
EFFECT
PROGRAM
YPAO
ZONE 3
R
L
OPTICAL
ZONE 2
AUDIO
VIDEO AUX
SILENT CINEMA
S VIDEO
VIDEO
PHONES
BAND
CATEGORY
PRESET/TUNING/CH
MONO
STEREO/
MODE
SEARCH
MEMORY
STRAIGHT
CONTROL
SELECT
AUDIO
TONE
ENTER
ON/OFF
WIRELESS
LAN
WIRELESS
LAN
NETWORK MUSIC COMMANDER MCX-RC100
ZONE
MUTE
MUSIC/
REMOTE
VOLUME
BACK
HOME
Receiver
(RX-V1900, etc)
Wired
WAN
(Net Radio, etc)
MCX-P200
(Music Player without amplifier)
MCX-A300
(Music Player with amplifier)
MCX-RC100
(Music Commander)
WiFi router
WiFi
Wired or WiFi
MASTER
PURE DIRECT
VOLUME
MAIN ZONE
INPUT
INFO
ZONE ON/OFF ZONE CONTROLS
MULTI ZONE
MIC
OPTIMIZER
EFFECT
PROGRAM
YPAO
ZONE 3
R
L
OPTICAL
ZONE 2
AUDIO
VIDEO AUX
SILENT CINEMA
S VIDEO
VIDEO
PHONES
BAND
CATEGORY
PRESET/TUNING/CH
MONO
STEREO/
MODE
SEARCH
MEMORY
STRAIGHT
MENU
REC OUT
AUDIO SELECT/
CONTROL
TONE
ENTER
USB
Network receiver
(RX-V3900, etc)
&
This guide assumes that you have an Internet connection and
your WiFi router is being connected to the Internet.
This guide is printed prior to production. Design and specifications
are subject to change in part as a result of improvements, etc.
•
•
1
Preparation
Charging the Music Commander (MCX-RC100)
First, charge the Music Commander (MCX-RC100) as shown below. It
takes about 135 minutes to fully charge the built-in battery.
�
AC adapter
y
The Music Commander automatically turns on by charge. If not,
press and hold the control pad for more than two seconds to turn on it.
How to use the Music Commander’s control
pad
• To move the selection from
side to side or up and down
• To move the page up and down
• To enter the highlighted menu or confirm the selection
y
Press the control pad until you hear click sound. It does not react to
a touch.
2
Cable connections
For MCX-A300
1
Connect front right and left speakers to the SPEAKERS (L/R)
terminals using speaker cables.
2
If desired, connect a subwoofer to the SUBWOOFER OUT jack
using a subwoofer (pin-jack) cable.
3
Plug the supplied AC adapter into the adapter connector, connect
the power cable to the AC adapter, and then plug into an AC wall
outlet.
POWER
USB
WPS
( LAN )
NETWORK
DOCK
SPEAKERS
SUBWOOFER OUT
DC IN 19V
OFF
ON
Subwoofer
Right
Front speakers
AC adapter
MCX-A300
Left
1
1
2
3
For MCX-P200
1
Plug an analog audio cable into the AUDIO (L/R) jacks.
2
Plug the other end of the analog audio cable into analog input jacks
available on your receiver (RX-V1900, etc).
3
If desired, connect a subwoofer to the SUBWOOFER jack using a
subwoofer (pin-jack) cable.
4
Plug the supplied AC adapter into the adapter connector, connect
the power cable to the AC adapter, and then plug into an AC wall
outlet.
CD
TV
DVD
(PLAY)
IN
CD-R
MD/
BD/HD DVD
VCR
DVR
CBL/SAT
IN
IN
POWER
USB
REMOTE CONTROL OUT
WPS
( LAN )
NETWORK
DOCK
SUBWOOFER
AUDIO
PRE OUT
DC IN 19V
OFF
ON
L
R
L
R
Subwoofer
AC adapter
Receiver (RX-V1900, etc)
MCX-P200
3
2
1
4
y
By using the supplied IR flasher, you can control the receiver
connected to the MCX-P200 with the Music Commander. For
details, refer to the online manual at the MusicCAST2 website.
For information on other connections for your receiver, refer to the
manual supplied with it.
•
•
For a network receiver (RX-V3900, etc)
1
Connect your network receiver to a LAN port of the WiFi router
using a network cable (CAT-5 or higher straight cable).
2
Plug the supplied power cable into the AC inlet and then plug into
an AC wall outlet.
NETWORK
AC IN
LAN
WAN
WiFi router
Network receiver (RX-V3900, etc)
To WAN
1
2
Power cable
y
For information on other connections for your network receiver,
refer to the manual supplied with it.
3
WiFi settings
y
If your WiFi router supports WPS, you can simply establish a
wireless connection between this WiFi router and the MusicCAST2
system using WPS. To activate the Music Players, press and hold
the WPS setup button more than one second. For complete details,
refer to the online manual at the MusicCAST2 website and WiFi
router manual.
1.
Make sure that your WiFi router is turned on.
2.
Music Commander:
ZONE
→
Setup
NETWORK MUSIC COMMANDER MCX-RC100
ZONE
MUTE
MUSIC/
REMOTE
VOLUME
BACK
HOME
ê
NETWORK MUSIC COMMANDER MCX-RC100
ZONE
MUTE
MUSIC/
REMOTE
VOLUME
BACK
HOME
ê
NETWORK MUSIC COMMANDER MCX-RC100
ZONE
MUTE
MUSIC/
REMOTE
VOLUME
BACK
HOME
3.
Control
pad
[Network] – [Setup] – [Wireless LAN] – [Easy Setup]
Use the control pad to select
[Network]
and enter the “Network” menu
as shown below. In the same way, select
[Setup] – [Wireless LAN]
– [Easy Setup]
.
NETWORK MUSIC COMMANDER MCX-RC100
ZONE
MUTE
MUSIC/
REMOTE
VOLUME
BACK
HOME
ê
NETWORK MUSIC COMMANDER MCX-RC100
ZONE
MUTE
MUSIC/
REMOTE
VOLUME
BACK
HOME
ê
NETWORK MUSIC COMMANDER MCX-RC100
ZONE
MUTE
MUSIC/
REMOTE
VOLUME
BACK
HOME
4.
Control
pad
Select a WiFi router to use for the WiFi
connection.
NETWORK MUSIC COMMANDER MCX-RC100
ZONE
MUTE
MUSIC/
REMOTE
VOLUME
BACK
HOME
ê
NETWORK MUSIC COMMANDER MCX-RC100
ZONE
MUTE
MUSIC/
REMOTE
VOLUME
BACK
HOME
(continued on the back side)
U
