background image

REMOTE CONTROL FUNCTIONS

REMOTE CONTROL FUNCTIONS  11

IMPORTANT NOTE:

The AVR 235’s remote may be

programmed to control up to eight devices, including
the AVR 235. Before using the remote, it is important to
remember to press the 

Input Selector Button

e

that corresponds to the unit you wish to operate.
In addition, the AVR 235’s remote is shipped from 
the factory to operate the AVR 235 and most
Harman Kardon CD or DVD players and cassette
decks. The remote is also capable of operating a 
wide variety of other products using the control codes
that are part of the remote. Before using the remote
with other products, follow the instructions on pages
35–36 to program the proper codes for the products
in your system.

It is also important to remember that many of the but-
tons on the remote take on different functions, depend-
ing on the product selected using the Device Control
Selectors. The descriptions shown here primarily detail
the functions of the remote when it is used to operate
the AVR 235. (See page 35 for information about
alternate functions for the remote’s buttons.)

a

Power Off Button:

Press this button to place the

AVR 235 or a selected device in the Standby mode.

b

IR Transmitter Window:

Point this window

towards the AVR 235 when pressing buttons on the
remote to make certain that infrared commands are
properly received.

c

Program/SPL Indicator:

This three-color indica-

tor is used to guide you through the process of pro-
gramming the remote, and it is also used as a level
indicator when using the remote’s EzSet capabilities.
(See page 23 for more information on setting output
levels, and see page 35 for information on program-
ming the remote.)

d

Power On Button:

Press this button to turn on

the power to a device selected by pressing one of the

Input Selectors

e

.

e

Input Selectors:

Pressing one of these buttons

will perform three actions at the same time. First, if the
AVR 235 is not turned on, this will power up the unit.
Next, it will select the source shown on the button as
the input to the AVR 235. Finally, it will switch the
remote control so that it controls the device selected.
After pressing one of these buttons, you must press
the 

AVR Selector Button

f

again to operate the

AVR 235’s functions with the remote.

f

AVR Selector:

Pressing this button will switch the

remote so that it will operate the AVR 235’s functions. If
the AVR 235 is in the Standby mode, it will also turn the
AVR 235 on.

g

AM/FM Tuner Select:

Press this button to select

the AVR 235’s tuner as the listening choice. Pressing
this button when the tuner is already in use will select
between the AM and FM bands.

h

Dim Button:

Press this button to activate the

Dimmer function, which reduces the brightness of the
front-panel display, or turns it off entirely. The first press
of the button shows the default state, which is full bright-
ness, by indicating 

VFD FULL

in the 

Lower

Display Line

¯

. Press the button again within five

seconds to reduce the brightness by 50%, as indicated
by 

VFD HALF

showing in the 

Lower Display Line

¯

. Press the button again within five seconds and the

main display will go completely dark. Note that this set-
ting is temporary in that, regardless of any changes, the
display will always return to full brightness when the AVR
is turned on. In addition, the 

Power Indicator

2

will

always remain at full brightness, regardless of the set-
ting. This is to remind you that the AVR is still turned on.

i

Test Button:

Press this button to begin the

sequence used to calibrate the AVR 235’s output levels.
(See page 23 for more information on calibrating the
AVR 235.)

j

Sleep Button:

Press this button to place the unit

in the Sleep mode. After the time shown in the display,
the AVR 235 will automatically go into the Standby
mode. Each press of the button changes the time until
turn-off in the following order:

This button is also used to change channels on your
TV when the TV is selected.

When the AVR 235 remote is being programmed with
the codes to operate another device, this button is also
used in the “Auto Search” process. (See page 35 for
more information on programming the remote.)

k

DSP Surround Mode Selector:

Press this but-

ton to cycle through the DSP, VMAx and Stereo sur-
round modes such as Hall, Theater, VMAx Near and
Far, and Surround Off. This button is also used to tune
channels when the TV is selected using the device

Input Selector

e

. When the AVR 235 remote is

being programmed with the codes of another device,
this button is also used in the “Auto Search” process.
(See page 35 for more information on programming
the remote.)

l

Night Mode:

Press this button to activate the

Night mode. This mode is available in specially 
encoded digital sources, and it preserves dialogue
(center channel) intelligibility at low volume levels.

m

Channel Select Button:

This button is used to

start the process of setting the AVR 235’s output levels to
an external source. Once this button is pressed, use the

/

¤

Buttons

n

to select the channel being adjusted,

then press the 

Set Button

p

, followed by the 

/

¤

Buttons

n

again, to change the level setting. (See

page 30 for more information.)

n

/

¤

Buttons:

These multipurpose buttons are

used to change or scroll through items in the on-
screen menus, make configuration settings such as
digital inputs or delay timing, or to select surround
modes. When changing a setting, first press the button
for the function or setting to be changed (e.g., press
the 

DSP Surround Mode Selector

k

to select a

sound field mode or the 

Digital Select Button

q

to change a digital input) and then press one of these
buttons to scroll through the list of options or to
increase or decrease a setting. The sections in this
manual describing the individual features and functions
contain specific information on using these buttons for
each application.

o

/

Buttons:

These buttons are used to change

the menu selection or setting during some of the setup
procedures for the AVR 235.

p

Set Button:

This button is used to enter settings

into the AVR 235’s memory. It is also used in the
setup procedures for delay time, speaker configuration
and channel output level adjustment.

q

Digital Select:

Press this button to assign one

of the digital inputs 

*(

ad

to a source. (See

page 26 for more information on using digital inputs.)

r

Numeric Keys:

These buttons serve as a 10-

button numeric keypad to enter tuner preset positions.
They are also used to select channel numbers when
TV, Cable or SAT has been selected on the remote, or
to select track numbers on a CD, DVD or LD player,
depending on how the remote has been programmed.

s

Tuner Mode:

Press this button when the tuner 

is in use to select between automatic tuning and
manual tuning. When the button is pressed so that

MANUAL

appears in the 

Lower Display Line

¯

,

pressing the 

Tuning Buttons

u9

will move the

frequency up or down in single-step increments. When
the FM band is in use, pressing this button when a
station’s signal is weak will change to monaural recep-
tion. (See page 29 for more information.)

90

min

80

min

70

min

60

min

50

min

40

min

30

min

20

min

10

min

OFF

AVR 235 OM  8/30/04  9:18 AM  Page 11

Содержание AVR 235

























































Отзывы: