Harken 7411.11 1/2.BLACK MKIV, Руководство по установке

Страница: 6 / 56

1. Stud/eye turnbuckle components are not included and
must be purchased separately. See page 8.
2. Rod rigging requires Harken rod adapter stud.
3. Order Harken Lead Blocks and one additional
7403 if necessary. Fits 1" (25 mm) stanchions.
Preassembly Rigging Parts Check/Tools
Tools You Will Need
MKIV Furlers are shipped with 3M 5200
adhesive. Use adhesives on dry connectors
and foils using the special injection system
described in the assembly section. Parts
may immediately be exposed to rain. Cure
is best at 70F (22C) with 50% humidity. Do
not apply at temperatures below 40F (5C)
and above 100F (38C).
Although adhesive has not cured it will
remain in place on foil joints whether
they are left on the ground or raised up
on boat. Foils can be raised immediately
after assembly and sails fitted.
Note: A small amount of adhesive may
bulge out of injection ports. If possible
let system sit for a couple days before
sailing. If adhesive gets on sails remove
using acetone. For faster-curing adhesive,
purchase 4200 Fast Cure.
Note: Damaged foils can be repaired.
Use a hand-held propane torch to heat
joints until foils can be pulled apart.
Adhesive Alert
Unit 1, 2
7404 Lead Block Kit
(Sold Separately)
1. Long tape measure 6. Side cutters 11. Center punch 16. Hole saw
2. Short tape measure 7. Rat-tail file 12. Rigging or black tape 17. Deck sealant
3. Power drill 8. Hex Keys (provided) 13. Scissors 18. Box end wrench
4. Drill bits (see chart) 9. Slotted/phillips screwdrivers 14. Metal straight edge 19. 6 mm bolts, nuts and washers
5. Hacksaw 10. Needle-nose pliers 15. Hammer
10
13
12
11
8
7
6
5
3
2
1
14
9
ROD RIGGING
Harken Rod Adapter
Stud Required
(Sold Separately)
Unit Part No. Thread Ø
1
7422 -8 1 /
2
" - 20RH
7423 -10 1 /
2
" - 20RH
2
7424 -12 5 /
8
" - 18RH
7425 -17 5 /
8
" - 18RH
3
7426 -22 3 /
4
" - 16RH
7427 -30 7 /
8
" - 14RH
Rod Adapter Stud
349, 2652
131, 047
Unit Turning Thru-Deck
1 349 131
2 2652 047
3 2600/137/071 HC7981
Recommended Furling
Compartment Lead Blocks
Unit
Deck
Flange Ø
Hole
Saw Size
1 3.7"
(94 mm)
3 ¾"
(95 mm)
2 4.2"
(106.5 mm)
4 ¼"
(110 mm)
3 5.45"
(138.5 mm)
5 ½"
(140 mm)
16
Unit
Wrench Size
for Length Adjuster
1
7
/
8
"
(22 mm)
2 1"
(25 mm)
3 1.25"
(32 mm)
18
Use 6 mm bolts and washers to
mount deck flange. To figure bolt
length, add
3
/
8
" (10 mm) to deck
thickness. Minimum thread
engagement must be 9mm.
19
17
4
Unit Drill Ø
1
1
/
8
"
(3 mm)
,
1
/
4
"
(6.25 mm)
2
5
/
32
"
(4 mm)
,
1
/
4
"
(6.25 mm)
3 (
3
/
4
,
7
/
8
)
5
/
32
"
(4 mm)
,
1
/
4
"
(6.25 mm)
15
6 MKIV Underdeck Unit 1, 2, 3