Harken 7411.11 1/2.BLACK MKIV Скачать руководство пользователя страница 41

Страница: 41 / 56

Operation

Race Conversion

Race conversion allows use of both

grooves for sail changes and tacking

genoas on deck for use of maximum

luff length genoas.

Halyard Swivel Off Furler

Serious racers may want to remove the

halyard swivel.

1) Remove drum assembly.
2) Rig a secure, temporary headstay.
3) Loosen backstay, mainsheet and vang

so that headstay goes slack.
4) See procedure on pages 29 - 31.

Note:

It is not possible to remove halyard

swivel on a unit with a Norseman/Sta-Lok

or rod adapter stud unless you disassemble

terminal stud. Make sure you use a new

Norseman/Sta-Lok

wedge to reassemble

Norseman/Sta-Lok

fitting.

Halyard Swivel Below Feeder

Use halyard to lift halyard swivel up, away

from feeder. Loosen screw

one revolution

only

. Slide screw up and hold. Remove

feeder carefully—bottom end first.

Don’t

lose the feeder overboard!

Lower swivel

onto torque tube. Replace feeder.

Remove Feeder

Loosen screw

one revolution only

. Slide screw up and hold.

Carefully remove feeder–bottom

end first.

Don't drop the feeder

overboard!

1. Loosen screw

one revolution only.

2. Slide screw up.

Remove feeder.

3. Lower halyard

swivel.

To Remove

Feeder For

Racing

MKIV Underdeck Unit 1, 2, 3

Содержание 7411.11 1/2.BLACK MKIV

























































Результаты поиска

Содержание 7411.11 1/2.BLACK MKIV

Отзывы:

Бренды по названию

Популярные бренды

Harken 7411.11 1/2.BLACK MKIV, Руководство по установке

Результаты поиска

Содержание 7411.11 1/2.BLACK MKIV

Отзывы:

Бренды по названию

Популярные бренды