Harken 7411.11 1/2.BLACK MKIV Скачать руководство пользователя страница 11

Страница: 11 / 56

Assembly

Assemble Drum Components

Place halves of plastic flange in

lower groove on hub assembly

so smooth side of flange is up.

Tip: Line up flats in flange with

flats in groove.

Place halves of plastic cover in

grooves so flats in cover align

with flats in groove.

Tip: Rotate each screw hole

towards the stern.

Use blue Loctite

on flathead

screws (provided).

Use blue Loctite

on flathead

screws (provided).

Assemble line guard so enclosed

opening faces lead block. Do not

use Loctite

on threads.

Tip: Loosely thread both screws

turning guard so it can be rotated

to its final position. Finish

tightening final screw when

enclosed opening faces lead

block.

Tighten screws using hex key

(provided).

Tighten screws using hex key

(provided).

MKIV Underdeck Unit 1, 2, 3

Содержание 7411.11 1/2.BLACK MKIV

























































Результаты поиска

Содержание 7411.11 1/2.BLACK MKIV

Отзывы:

Бренды по названию

Популярные бренды

Harken 7411.11 1/2.BLACK MKIV, Руководство по установке

Результаты поиска

Содержание 7411.11 1/2.BLACK MKIV

Отзывы:

Бренды по названию

Популярные бренды