manualshive.com logo in svg

Harken 7411.11 1/2.BLACK MKIV, Руководство по установке

Поделиться
Скачать
Harken 7411.11 1/2.BLACK MKIV Скачать руководство пользователя страница 38

Operation 

Halyards/Headstay Tension

Backstay Adjusters

Backstay adjusters allow headstay tension to be varied to change sail shape to match 

conditions. They permit a very tight headstay to be eased when boat is not in use.  

For best performance, consider adding a backstay adjuster; either a block and tackle, 

a mechanical adjuster like those offered by Harken, or a hydraulic adjuster.
Remember to keep headstay tight for best performance when furling or reefing.
If your boat is fitted with an adjuster be sure that it is tensioned 

before

 the  

halyard is tensioned. If not, backstay adjuster may increase halyard tension  

and could damage the sail or furling system.
Racing boats often slack the headstay completely when sailing downwind. 

Check to be sure that foil does not jam against upper headstay terminal when 

backstay is released. To prevent this, it may be necessary to shorten foil slightly.

38 

MKIV Underdeck Unit 1, 2, 3 

On many boats it will not be possible to attach spinnaker 

halyard to bow pulpit or it may be "sucked" into jib when 

furling.
On some boats the spinnaker halyard lays across  

headstay and will catch on halyard swivel, foils or  

jib halyard. To prevent problems it may be necessary  

to install a masthead bail to move spinnaker halyard 

block forward and to one side. 
Boats with external halyards may find it necessary to  

flip both ends of spinnaker halyard behind spreaders  

to prevent fouling with furling system.

Headstay Tension

A furling system will work best if headstay is tight. 
A loose headstay is difficult to rotate and can cause 

unusual wear on foil joints.
To adjust headstay tension, remove sail and furling line 

from unit and follow instructions on page 30.

Tip: Before adjusting headstay tension, slack  

mainsheet and vang.

Spinnaker Halyards

Spinnaker halyards occasionally cause problems  

with furling.

WARNING! In severe cases, spinnaker halyards 

can jam furler causing loss of control of boat 

which can cause an accident, damage to your 

vessel, personal injury or death. See www.

harken.com/manuals for additional safety  

information.

Содержание 7411.11 1/2.BLACK MKIV

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды