Hardy H3 Скачать руководство пользователя страница 44

Страница: 44 / 46

HARDY MANUFACTURING CO., INC (MODEL H3, H5, & H6) PAGE 34

Section VII 7 – 5

Trouble Shooting Guide H3,H5,&H6

COMPLAINT

AREA OF TROUBLE

POSSIBLE CAUSES

CORRECTIVE ACTION

Water not circulating
through the heat loop

Pump not operating

Inline valves closed/bad

Air trapped in plumbing

Scale deposits in hot
water coil reducing
water flow and
restricting heat transfer.

Air lock in hot water
coil.

See area of trouble: “Pump
Operation”

Open or replace valves

Bleed lines if air is trapped
non pressured lines require
pump to be running.

Disconnect the inlet and
outlet of the hot water coil
and pump clean with descale
cleaning kit.

Bleed air from hot water coil

NO HEAT

Blowing cold air
in house

Water
temperature is
“HOT”

Power “OK”

Excessive wood
usage

Overheating
(boiling)

Heater water boils

(Symptom –Popoff valve is
relieving)

Doors open

Defective door seals

Damper blower lid
stuck open

Damper aquastat
defective

Water lines /
connections leaking

Close all doors and make
sure they are securely
fastened.

If the seal is bad it will need
replacing. Call your local
Hardy Dealer for parts. See
Owners Manual for replacing
door seals.

Unplug blower motor. Check
lid and blower for creosote
buildup. Remove blower,
dissemble, clean, and oil.

Check temperature setting on
aquastat. Should be 170ºF. If
aquastat is allowing blower to
run until water boils, replace
aquastat.

Repair or replace all lines or
connections that are leaking.

Содержание H3















































Результаты поиска

Содержание H3

Отзывы:

Похожие инструкции для H3

Бренды по названию

Популярные бренды

Hardy H3, Инструкция по установке и эксплуатации

Результаты поиска

Содержание H3

Отзывы:

Похожие инструкции для H3

Бренды по названию

Популярные бренды