Hardy H3 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 46

background image

INTRODUCTION

Thank you

for purchasing the original all stainless steel Hardy Outside Wood Burning

Heater. It represents the result of many years of Hardy experience and the input of Hardy
customers in the production of a top quality heater. With the purchase of this Hardy Heater,
you can now appreciate the high degree of craftsmanship and reliability that have made The
Hardy the leader in the outside woodburning heater field. This manual will provide you with a
good basic understanding of the installation and operation of this heater.

THIS MANUAL INCLUDES IMPORTANT SAFETY INFORMATION

Your new heater should have the following:

(1)

Owner’s manual complete with Installation
and Hook-Up Instructions

(2)

Warranty & Return Warranty Card

(3)

A tube of silicon (located in the firebox for shipping)

(4)

Smoke stack and condenser tank stack both
with trim (located in firebox for shipping)

(5)

Three cast iron grates (located in firebox)

(6)

Two I - beam & 2 Channel Beams (located in firebox)

(7)

Shovel (located in the firebox for shipping)

(8)

Stainless steel panel and insulation that will be
located between the firebox door & ash door
after installation of the heater

(9)

Stainless steel flame baffle (15” x 10”). Only for
use on Hardy model H5 180,000 BTU heater

Should your heater not have any of these items or if you have any questions regarding the
operation or maintenance of your heater, please consult you local Hardy dealer.

Again, thank you for purchasing a Hardy Heater.

Sincerely,

Frank L. Moore

President

Hardy Manufacturing Company Incorporated

(MODEL H3 H5 & H6)

i

«
1
2
3
4
5
...
»

Содержание H3















































Отзывы:

Нет отзывов

Похожие инструкции для H3

Бренд: HAMPTON BAY Страницы: 32

Бренд: Jøtul Страницы: 32

Бренд: Duraflame Страницы: 18

Бренд: Zibro Страницы: 12

Бренд: Broseley Страницы: 62

Бренд: CombiSteel Страницы: 18

CLASSIC BAY 1200

Бренд: Quadra-Fire Страницы: 30

Бренд: Country Hearth Страницы: 20

Бренд: COUNTRY FLAME TECHNOLOGIES Страницы: 58

Бренд: Astra Страницы: 28

Бренд: Sterno Inferno Страницы: 1

Бренд: Henley Stoves Страницы: 9

Бренд: F2 Fires Страницы: 20

Бренд: Kuma Stoves Страницы: 12

Бренд: Kuma Stoves Страницы: 30

Бренд: Kuma Stoves Страницы: 30

Бренд: Viadrus Страницы: 24

Thermofan 731 MF

Бренд: Defy Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды