Hardinge SERIES I Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 23

background image

MOTOR

Motor “Q”, Figure 2.15, has the following specifications:

• 2 HP variable speed (with 2J head)

• 3 HP 30 minute duty rate

DRAWBAR

When tightening or loosening the Drawbar “R”, Figure 2.15, it is necessary to lock the spindle. To

accomplish this, use the spindle brake which is located on the left side of the belt housing, pulling
towards the operator or pushing away from the operator until it binds, then raise the quill feed handle.

Drawbar has 7/16”-20 right hand thread and should be tightened by hand with normal amount of

pressure using wrench furnished with machine. To loosen collet, back off drawbar and if collet does
not open immediately, give knob on top of drawbar a slight tap. Spindle has non-sticking taper and
collet should release readily.

M-450

2-9

Figure 2.15 - Motor and Drawbar

TP5299

Q

R

«
...
8
9
10
11
12
...
»

Содержание SERIES I
























Отзывы:

Нет отзывов

Похожие инструкции для SERIES I

Бренд: Makita Страницы: 16

Бренд: Mafell Страницы: 46

Бренд: Panduit Страницы: 16

Бренд: Panduit Страницы: 2

BT-CK 18 2B-1.5 Kit

Бренд: Taurus Страницы: 40

Бренд: Elmdene Страницы: 8

Бренд: Robust Страницы: 44

Бренд: Wacker Neuson Страницы: 54

Бренд: Air & Allied Sales Страницы: 11

Бренд: Feider Machines Страницы: 15

Бренд: Powerfix Profi Страницы: 75

Бренд: Paslode Страницы: 32

Бренд: Hama Страницы: 36

Бренд: M7 Страницы: 14

Бренд: Parkside Страницы: 109

Бренд: Echo Страницы: 24

Бренд: APE Страницы: 45

Бренд: Bohmer-AG Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды