HARD 1935 Скачать руководство пользователя страница 38

Страница: 38 / 46

CASTERS & MISC

Position of the casters is determined by standing at the foot end of the crib.

1 & 2

Heavy duty casters
*BC-65 with large bolt in
stem.

On cribs and beds made
2015 to present.

Old style brake caster
72104 with narrow stem
used with a black plastic
caster socket.

On cribs and beds made
prior to 2015.

Part Description

Part #

Notes

5” Heavy Duty Casters- 2015 to present

*BC-65

Full set with hardware- 1 Steer,

2 Brake, 1 Swivel & Hardware

1 Steer Caster

72100

Located at head end right side

2 Brake Caster

72101

Located at head end left side

and foot end right side

3 Swivel Caster

72102

Located at foot end left side

4 Bolt- 8-8x10mm

61007

2 per caster

5” Casters- Full set includes: 2 Brake,
2 Swivel & 3 Caster Sockets

*BC-15

See below. This set of casters is on

hospital cribs manufactured prior to 2015

Brake Caster

72104

Swivel Caster

72105

Caster Socket

60606

Bright White Touch Up Paint- 1/4 pint

00564

Enamel based paint

Antique White Touch Up Paint- 1/4 pint

00562

Содержание 1935















































Результаты поиска

Содержание 1935

Отзывы:

Бренды по названию

Популярные бренды

HARD 1935, Руководство по обслуживанию

Результаты поиска

Содержание 1935

Отзывы:

Бренды по названию

Популярные бренды