manualshive.com logo in svg

HARD 1935, Руководство по обслуживанию

Поделиться
Скачать
HARD 1935 Скачать руководство пользователя страница 14

SIDE RAIL ASSEMBLY PARTS LIST

#

Part Description

Part #

Notes

1

Side Trim Assembly- 1935

90451

Complete Side Rail Assembly

Side Trim Assembly- 1943 & 1955

90222

Side Trim Assembly- 1975

90456

2

Side Trigger Assembly- 1935

89115

One trigger per rail

Side Trigger Assembly- 1943 & 1955

89117

Side Trigger Assembly- 1975

89119

Teething Bars- 1935

*1935 TB

Not  shown.  Set  of  3-

Protective covering for the 

tops of the rails. 

Teething Bars- 1943

*1943 TB

Teething Bars- 1955

*1955 TB

Teething Bars- 1975

*1975 TB

3 Glide Slide Bushing

11571

Nylon bushing with cutout

4 Bushing

11518

Solid nylon bushing

5 Johns Hopkins Handle Assembly

72115

Complete Handle Assembly                    

(Does not include Shield Plate)

6 Screw 10-32x1 RH PH MS

63375

Components  at  the  bottom  of  the                      

Johns Hopkins Handle

7 Retainer Block

11525

8 Split Lockwasher 

63453

9 Acorn Nut C/P 10-32

63411

10 Screw

60148

Top of Shield Plate

11 Split Washer

63457

12 Shield Plate Assembly

81216

Plate  behind  JH  Handle

(Does not include handle)

13 HARD Sticker

62177

Sticker behind JH Handle Assembly

14

“To Lower Side Lift Then Squeeze” 
Sticker

63651

Placed above JH Handle

15

“To Raise Side Use Two Hands” 
Sticker

63650

Placed on either end of the side rail

14

Содержание 1935















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды