manualshive.com logo in svg

HARD 1935, Руководство по обслуживанию

Поделиться
Скачать
HARD 1935 Скачать руководство пользователя страница 18

FOOT END ASSEMBLY DIAGRAM & PARTS LIST

3

*Note- If your crib was made prior to 2015 or of your foot end curtain does not have a chart 
pocket, the Foot End Assembly parts listed above do not apply. Please contact us for the 
correct part numbers.

2

Foot Trim Assembly
              1

4

#

Part Description

Part #

Notes

1

Foot Trim Assembly- 1915, 1935, 1943

90352

Complete Foot Assembly

Foot Trim Assembly- 1955 & 1975

90353

2

Foot Weld Assembly- 1915, 1935, 1943

82914

Outside  head  end  frame  only,                                

no curtain assembly 

Foot Weld Assembly- 1955, 1975

82917

3

Foot Curtain Only- 1915, 1935 & 1943

63340

*Curtain  has  a  chart  pocket                                                  

as a standard feature. 

Foot Curtain Only- 1955 & 1975

63770

4

End Curtain Retainer- 1915, 1935 & 1943

11173 Metal bar that holds the bottom of the curtain 

to the crib frame. Screws not included.

End Curtain Retainer- 1955 & 1975

11132

5 Screw for Retainer (Not shown)

63386

Not shown

18

Содержание 1935















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды