background image

Page 4

for technical questions, please call 1-800-444-3353.

SKU 67378 

        

is any question about a condition 

being safe of unsafe, do not operate 

the Tool.

Keep the metal Detector away from 

8. 

any lights, tVs, computers, and 

moble telephones. 

 These can all 

cause electro-magnetic interference.

only the Search coil (23) and 

9. 

plastic section of the lower 

leg (18) are water proof. 

Do not 

immerse the unit any further into 

water beyond the plastic section of 

the Lower Leg.

Keep the tool clean.  

10. 

Wipe the 

housing after each use.  The search 

coil is washable and can be fully 

submerged.  Never submerge the 

control housing.  Protect the control 

housing from rain, blowing surf and 

heavy mist.  Disassemble the Leg 

and wipe it clean after use in sandy 

areas.

use the right tool for the job

11. 

.  

There are certain applications for 

which this tool was designed. Do not 

modify this tool and do not use this 

tool for a purpose for which it was not 

intended.

this product is not a toy. 

12. 

 Keep it 

out of reach of children.

people with pacemakers should 

13. 

consult their physician(s) before 

use. 

 Electromagnetic fields in close 

proximity to heart pacemaker could 

cause pacemaker interference or 

pacemaker failure.  In addition, 

people with pacemakers should: 

• Avoid operating alone.

 

• Properly maintain and inspect to 

avoid electrical shock.

Warning:

14. 

 This product contains 

or, when used, produces a chemical 

known to the State of California to 

cause cancer and birth defects or 

other reproductive harm.  (California 

Health & Safety Code §  25249.5, 

et 

seq.

The warnings, precautions, 

15. 

and instructions discussed in 

this instruction manual cannot 

cover all possible conditions and 

situations that may occur.  It must 

be understood by the operator that 

common sense and caution are 

factors which cannot be built into this 

product, but must be supplied by the 

operator.

  SaVe theSe 

inStructionS.

Содержание 67378














Отзывы: