background image

NOTE:

 A small amount of "wobble" is normal and should not be considered a defect.

      WARNING:

 Before beginning work, shut off the power supply to avoid electrical shock.

PROBLEM

POSSIBLE CAUSE

CORRECTIVE ACTION

Fan does not move. 1. Reverse switch not engaged.

2. Power is off or fuse is blown.

3. Faulty wire connection.

4. Plugs not connected properly.  

1. Push switch firmly either left or right.

2. Turn power on or check fuse. 

3. Turn power off. Loosen canopy and 

check all connections.

4. Check that wire nuts from fan and  

receiver to the outlet box are 

connected properly according to 

instructions on page 10.

Noisy operation.

1. Blades are loose.

2. Cracked blade.

3. Full range dimmer switch.

4. Fan is new. 

1. Blades are loose.

2. Blade arms incorrectly attached.

3. Unbalanced blades.

4. Fan not securely mounted.

5. Fan too close to vaulted ceiling.

6. Set screw(s) on motor housing 

    yoke is (are) not tightened properly.

7. Set screw on hanging ball is not 

tightened properly.

1. Tighten all blade screws.

2. Replace blade.

3. Replace with an approved speed 

control device.

4. Allow fan a “break in” period of a 

few days, especially when running 

the fan at Medium and High 

speeds.

Excessive wobbling.

1. Tighten all blade screws.

2. Re-install blade arms.

3. Switch one blade with a blade 

from the opposite side. Or balance 

the fan using a blade balancing kit 

(sold separately).

4. Turn power off. Carefully loosen 

canopy and verify that mounting 

bracket is secure.

5. Use a longer downrod or move 

fan to another location.

6. Tighten yoke set screw(s) 

securely.

7. Carefully loosen and lower canopy 

and verify that set screw on 

hanging ball is tightened securely.

Fan operates but

light fails.

1. Wires in canopy not wired properly.

2. Wall switch to fan is off.

3. Plugs not connected properly.

1. Check wires in canopy and, if 

    necessary, re-wire according to  

    instructions on page 10.

2. Make sure that wall switch to fan 

    is on.

3. Check that male and female plugs 

    in light kit are connected properly 

    according to instructions on page 

    13.

20

TROUBLESHOOTING

Содержание FARMINGDALE AR15-72BN













































Отзывы: