background image

2

Safety Information ................................................................................................................. 2

Package Contents ................................................................................................................. 5

Hardware Contents ........................................................................................................................... 6

Preparation ........................................................................................................................... 6

Initial Installation ................................................................................................................... 6

Wiring .................................................................................................................................. 10

Final Installation ................................................................................................................... 12

Operating Instructions ......................................................................................................... 16

Care and Maintenance ........................................................................................................ 17

Troubleshooting ................................................................................................................... 18

Limited Lifetime Warranty .................................................................................................... 19

Replacement Parts List ....................................................................................................... 19

TABLE OF CONTENTS

SAFETY INFORMATION

         CAUTION:

 Changes or modifications not approved by the party responsible for compliance 

could void the user's authority to operate the equipment.

*NOTE: This equipment has been tested and found to comply with the limits for a Class B digital 
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable 
protection against harmful interference in a residential installation. This equipment generates, uses 
and can radiate radio frequency energy and, if not installed and used in accordance with the 
instructions, may cause harmful interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular installation. If this equipment does cause 
harmful interference to radio or television reception, which can be determined by turning the 
equipment off and on, the user is encouraged to try to correct the interference by one or more of the 
following measures:
        *      Reorient or relocate the receiving antenna.
        *      Increase the separation between the equipment and receiver.
        *      Connect the equipment into an outlet on a circuit different from that to which the receiver is 
 

          connected.

Consult the dealer or an experienced radio/TV technician for help.

The device complies with Part 15 of the FCC Rules. Operation is subject to the following two 
conditions: (1) this device may not cause harmful interference, (2) this device must accept any 
interference received, including interference that may cause undesired operation.

Distributed by: Litex Industries Inc., P.O. Box 535639, Grand Prairie, TX, 75050; 800-527-1292

NOTE:

 Dimmable to 10%.

Содержание EUK60MBK10LR




















Отзывы: