4
English
Assembly
(see page 33)
Safety Notes
Gloves should be worn during installation to prevent
crushing and cutting injuries.
Installation Instructions
• Suitable for renovation work and new buildings
• The product should only be installed by specialist
companies in compliance with the building regulations.
• To achieve the best possible result, please read the
installation guide carefully.
• Before starting the installation, the installation instruc-
tions with their specifics should be discussed with the
tiler. Please hand all installation instructions to the tiler
after installation.
• Prior to installation, inspect the product for transport
damages. After it has been installed, no transport or
surface damage will be honoured.
• When using the drain in conjunction with several
showers, please check if the draining capacity of the
drain is adequate.
• We recommend taping off the drain opening of the
drain set or closing it with the cement cap before
installation to prevent construction debris from getting
into the drain pipe.
• To prevent damage to the tile frame, it should be kept in
its packaging until final installation by the tiler.
• Align the drain horizontally in all directions.
• The installation of the waste water system must be
carried out in accordance with the standards. Pay
attention to adequate aeration and ventilation, and an
adequate slope in the waste water system.
• Check the drain system and the waste water connec-
tions for tightness.
• To prevent any cavities, the drain body must be fully
lined and compacted with screed up to the top edge of
the flange.
• Sealing is carried out in accordance with DIN 18534.
When using alternative sealing materials, the product
information provided by the manufacturer must be
observed.
• When laying the floor tiles, the tile slope (min. 2%) in
the shower area must always slope towards the drain.
The tiles must be laid flush or 1 mm higher than the top
edge of the tile frame. This ensures good drainage
towards the drain set. Other requirements regarding the
slope may apply for floor-level showers with glass walls.
The manufacturer's specifications must be observed.
• After tiling, the transition between the tiled floor and the
drain must be sealed with a permanently elastic joint
(maintenance joint). The bonding surfaces must be free
of mortar, adhesive and other adhesion-inhibiting
materials.
• The drain is only suitable for normal domestic waste
water. Avoid other liquids as well as cleaning agents
that can damage sanitary fitments, draining facilities
and pipe materials.
• When using the drain in other areas (e.g. swimming
pools) where the drain may come into contact with
aggressive cleaning agents or corrosive substances such
as salt or chlorine, please contact the manufacturer.
• Compliance with this installation recommendation is
required to make any warranty claims based on our
terms and conditions of sale and delivery.
• Products containing chlorine or acids, such as cement
residue remover or similar, often contain aggressive
chemicals. These can corrode the surface of the
product. Bleaches or silver cleaning agents are also
unsuitable for stainless steel care. When using tile and
joint cleaners, the product must subsequently be cleaned
with adequate amounts of clear water. The product
cannot be cleaned with abrasive cleaners and / or
pointed or abrasive objects. Clean brushed or ground
surfaces always parallel to the grind instead of across it.
Symbol description
Do not use silicone containing acetic acid!
Dimensions
(see page 32)
Cleaning
(see page 39)
• Before cleaning, remove all parts of the siphon and
clean them separately using only mild detergents.
Spare parts
(see page 41)
English
Содержание RainDrain Flex wall 56043 Series
