background image

Recommendations for Users

Before using this product, make sure that it is entirely suitable for the environment in which it is used.

Operation of this instrument in residential area could cause unacceptable interferences to radio and TV
equipments, requiring the operator to take all necessary steps to correct interferences.

Any variation introduced by the user to the supplied equipment may degrade the instrument's EMC
performance. To avoid electrical shock, do not use this instrument when voltages at the measurement
surface exceed 24 Vac or 60 Vdc.

To avoid injury or damage to the meter, do not perform any measurement in microwave ovens.

CE DECLARATION OF CONFORMITY

HI 710005

12 Vdc / 115 Vac voltage adapter, US plug

HI 710006

12 Vdc / 230 Vac voltage adapter, European plug

HI 731318

Tissue for wiping cuvettes ( 4pcs)

HI 731321

Glass cuvet (4 pcs)

HI 731325

Cap for cuvette (4 pcs)

HI 93703-0

Calibration solution AMCO-AEPA-1 @0 FTU, 30 mL

HI 93703-05

Cal. solution AMCO-AEPA-1 @500 FTU, 30 mL

HI 93703-10

Calibration solution AMCO-AEPA-1 @10 FTU, 30 mL

HI 93703-50

Cuvette cleaning solution, 230 mL

ACCESSORIES

WARRANTY

All Hanna Instruments

 meters are warranted for two years

against defects in workmanship and materials when used for their
intended purpose and maintained according to instructions. This
warranty is limited to repair or replacement free of charge.
Damage due to accident, misuse, tampering or lack of prescribed
maintenance are not covered.
If service is required, contact the dealer from whom you purchased the
instrument. If under warranty, report the model number, date of
purchase, serial number and the nature of the failure. If the repair
is not covered by the warranty, you will be notified of the charges
incurred. If the instrument is to be returned to Hanna Instruments,
first obtain a Returned Goods Authorization number from the Cus-
tomer Service department and then send it with shipping costs
prepaid. When shipping any instrument, make sure it is properly
packaged for complete protection.

All rights are reserved. Reproduction in whole or in part is
prohibited without the written consent of the copyright owner.

Hanna Instruments reserves the right to modify the design, con-
struction and appearance of its products without advance notice.

Содержание LP 2000










Отзывы: