Hangar 9 Hangar 9 P-51 Mustang ARF Скачать руководство пользователя страница 2

Страница: 2 / 48

Introduction ........................................................................................................................................ 3

Warning .............................................................................................................................................. 3

Additional Required Equipment ......................................................................................................... 4

Contents of Kit.................................................................................................................................... 5

Section 1: Hinging the Ailerons .......................................................................................................... 6

Section 2: Joining the Wing Halves.................................................................................................... 8

Section 3: Installing the Aileron Servos ..............................................................................................10

Section 4: Installing the Aileron Control Horns and Linkages ............................................................13

Section 5: Installing the Retract Servo ...............................................................................................15

Section 6: Installing the Main Landing Gear Wheels and Fairings......................................................18

Section 7: Mounting the Wing to the Fuselage................................................................................. 20

Section 8: Installing the Tail Group (Horizontal and Vertical Fin) ..................................................... 23

Section 9: Hinging the Elevators .................................................................................................... 27

Section 10: Installing the Rudder and Tail Wheel Assembly ........................................................... 29

Section 11: Installing the Elevator and Rudder Control Horns.......................................................... 32

Section 12: Assembling the Fuel Tank.............................................................................................. 34

Section 13: Mounting the Engine ..................................................................................................... 36

Section 14: Installing the Radio System ........................................................................................... 38

Section 15: Installing the Rudder, Elevator, and Throttle Linkage ..................................................... 40

Section 16: Attaching the Cowl ........................................................................................................ 42

Section 17: Application of Decals and Scale Detailing ..................................................................... 44

Section 18: Attaching the Canopy .................................................................................................... 46

Section 19: Balancing and Control Throw Recommendations .......................................................... 46

Preflight at the Field.......................................................................................................................... 47

AMA Safety Code.............................................................................................................................. 47

Table of Contents

Содержание Hangar 9 P-51 Mustang ARF

















































Результаты поиска

Содержание Hangar 9 P-51 Mustang ARF

Отзывы:

Похожие инструкции для Hangar 9 P-51 Mustang ARF

Бренды по названию

Популярные бренды

Hangar 9 Hangar 9 P-51 Mustang ARF, Инструкция по эксплуатации

Результаты поиска

Содержание Hangar 9 P-51 Mustang ARF

Отзывы:

Похожие инструкции для Hangar 9 P-51 Mustang ARF

Бренды по названию

Популярные бренды