background image

Specifications

• Wingspan: ................................................................................................................ 69in
• Length: ..................................................................................................................... 55in
• Wing Area:  ....................................................................................................... 793 sq in
• Weight (approximate): ....................................................................................... 6

1

/

4

–7 lb 

• Engine Supplied: ........................................................... Evolution Trainer Power System

• Ready to fly in less than one hour
• Comes with engine, radio, and control linkages installed
• No glue required for assembly (no smell, no mess)
• Precovered and trimmed in genuine UltraCote

®

• Two Fun options available: Sailplane Launch and Photo OP 

(camera not included)

Additional items required to get the Xtra Easy 2 into the air:

• Hangar 9 Start-Up Field Pack, which includes glow plugs, fuel pump, 

4-way wrench,  glow plug igniter with charger, 
Start Stick and tote box (HANSTART)

• Glow Fuel (10% or 15% nitro content recommended) (HAN3109–3115)

TM

TM

TM

Ver. 1.0

INSTRUCTION MANUAL

Содержание Extra Easy XE2

























Отзывы: