background image

7

There are multiple ways to level your floor frame. Our recommended leveling method is shown below.

 

Leveling materials are not included in this kit.

PREFERRED METHOD - 4x4 TREATED RUNNERS

Measurements to 

centers of 4x4's.

• 3" Screws 

  angled into 4x4.

• (2) at each point frame

 and 4x4 touch.

12"

(30,5 cm)

12"

(30,5 cm)

• Level under 4x4 runners only.
• Locate leveling material 12" (30,5 cm) from ends of runners and no more than 48" (121,9 cm) apart.
• Asphalt shingles should be used between 4x4 runners and blocks or treated lumber. Never use

 

   shingles in direct contact with ground. 

• For best results and aiding in water drainage use gravel under each concrete block.

LEVELING METHODS

• 

If you are building your shed on a concrete foundation see the following page.

CONCRETE

MATERIAL REQUIRED

x2

4 x 4 x 12' (10,2 x 10,2 x 365,8 cm)

Treated Lumber

Fasteners for Frame to 4x4.

 

(3" screws shown as one option.) Minimum (40) 3" screws / exterior grade.  

Use only wood treated for ground contact and fasteners approved for use with treated wood.

Always support frame seams.

Leveling higher than 16" (40,3 cm) not recommended.

LEVELING MATERIALS

Gravel

2x4 Treated Lumber

Solid Masonry Blocks in 1", 2", 4" or 8" thickness

Asphalt Shingles

8" Block

8" Block

4" Block

Gravel

Gravel

4x4 Runner

Shingle

Shingle

Maximum between leveling 

material locations.

48"

(121,9 cm)

12"

(30,5 cm)

12"

(30,5 cm)

2x4 Treated Lumber

2" Block

Level

Do not exceed 16" 

(40,3 cm).

Содержание Meridian 8' x 12' Gable 16698
































































Отзывы: