background image

LIMITED CONDITIONAL WARRANTY*

Backyard Storage Solutions, LLC warrants the following:

1. 

Every product is warranted from defects in workmanship and manufacturing for 1 year.

2. 

All accessories, hardware and metal components are warranted for 2 years.

3. 

All Oriented Strand Board (OSB) is warranted for 2 years

4. 

Siding and Trim is warranted for 15 years.

5.

LP Prostruct® Flooring is warranted for 10 years

6. 

Cedar lumber is warranted for 15 years.

7. 

Preserved Pine is warranted for 10 years.

8. 

Redwood is warranted for 10 years.

9. 

Metal Roof is warranted for 25 years.

Backyard Storage Solutions, LLC will repair, replace or pay for the affected part.  In no event shall Backyard Storage Solutions, LLC 

pay the cost of labor or installation or any other costs related thereto.  All warranties are from date of purchase.  If a cash refund is paid 

on an affected part, it will be prorated from the date of purchase.

CONDITIONS

The warranty is effective only when:

1. 

The unit has been erected in accordance with the assembly instructions. 

2. 

The unit has been properly shingled and painted or stained and reasonably and regularly maintained thereafter.

3. 

The failure occurs when the unit is owned by the original purchaser.

4. 

Backyard Storage Solutions, LLC has received the warranty registration card within thirty (30) days of purchase and

 

notification of the failure in writing within the warranty period specified above.

5. 

Backyard Storage Solutions, LLC has had reasonable opportunity during the sixty (60) days following receipt of notification to

 

inspect and verify the failure prior to commencement of any repair work.

REQUIREMENTS

Storage Buildings

To validate your warranty, it is necessary to properly maintain your Backyard Storage Solutions, LLC unit; shingle the roof and paint or 

solid-colored stain the siding using quality, 100% acrylic latex exterior product with a minimum of two (2) coats within thirty (30) days of 

assembly; caulk above all doors and all horizontal and vertical trim boards; paint and seal all exposed edges, sides and faces of 

siding/trim and OSB siding to include all exterior walls and all sides and all edges of doors.  

Gazebos & Pergolas

To validate your warranty, it is necessary to properly maintain your Backyard Storage Solutions, LLC unit.  This includes treating all of 

the exposed cedar and pine surfaces on your gazebo or pergola structure with an exterior grade wood preservative, an exterior 

oil-based semi-transparent stain, an acrylic latex exterior paint or an acrylic latex solid color exterior stain within 30 days of assembly 

and as needed thereafter to maintain your warranty.

Keep vegetation trimmed away from building and make sure siding panels and trim do not come in contact with masonry or cement.  

The minimum ground clearance for siding must be one half inch (½ inch) from concrete slab or two and one half inches (2 ½”) from the 

ground when building is erected or constructed on a treated wood floor kit. Water from sprinklers must be kept off unit. In no event will 

Backyard Storage Solutions, LLC be responsible for any indirect, incidental, consequential or special damages nor for failure(s) that 

are caused by events, acts or omissions beyond our control including, but not limited to, misuse or improper assembly, improper 

maintenance (which eventually leads to rot or decay) and acts of God. Backyard Storage Solutions, LLC will not be held responsible for 

any labor costs incurred to construct your unit.

This warranty gives you certain specific rights that vary from state to state.

CLAIM PROCEDURE

To make a claim under this warranty, you can either call 1-888-827-9056 or email: [email protected].

 Please have ready the information below when you call or include the information in your email:

1. 

The model and size of the product.

2. 

A list of the part(s) for which the claim is made.

3. 

Proof of purchase of the Backyard Storage Solutions, LLC item, as shown on the original invoice or receipt.

4. 

Run code: found on exterior product label or assembly instructions enclosed in the product package.

All other inquiries can be mailed to:

 

Backyard Storage Solutions, LLC

 

Attn: Customer Service

 

1000 Ternes

 

Monroe, MI 48162

 *WARRANTY TERMS MAY VARY OUTSIDE THE U.S.A.

IMPORTANT:  This is your warranty certificate.

15Y PSS BB GEN LDR:  3/20/2019

Содержание Meridian 8' x 12' Gable 16698
































































Отзывы: