Handy Home Products Meridian 8' x 12' Gable 16698 Скачать руководство пользователя страница 57

Страница: 57 / 63

• Follow directions provided by manufacturer and these instructions.

SHINGLES

- NOT INCLUDED -

Install first starter row upside down and color up with a 1" overhang at back and bottom of roof panel. Use (4) nails per shingle.

Starter row must be straight and level all the way across with lower edge of roof deck.

NOTE:

If you have installed drip edge install shingles flush to drip edge.

Beginning at front of shed, install first row of shingles with notch at 1" past roof edge or flush with drip edge.

BEGIN

TABS UP

Shingle overlaps

roof decking.

1" (2,5 cm) overhang

past roof deck.

1" (2,5 cm) overhang or

flush with drip edge.

(4) Nails

BACK OF

SHED

FRONT OF

SHED

FRONT OF

SHED

BACK OF

SHED

Notch

- or -

Drip Edge

Notch

Roof Deck

(2,5 cm)

Flush with starter row.

NEVER DRIVE FASTENERS INTO OR ABOVE SEALING STRIPS.

Familiarize yourself with a 3-Tab Shingle.

SHINGLE NAIL PATTERN

(2,5 cm)

NAILS

Sealing Strip

(2,5 cm)

1/2"

(1,3 cm)

Half A Rain Slot

Notch

Full Rain Slot

Содержание Meridian 8' x 12' Gable 16698
































































Результаты поиска

Содержание Meridian 8' x 12' Gable 16698

Отзывы:

Похожие инструкции для Meridian 8' x 12' Gable 16698

Бренды по названию

Популярные бренды

Handy Home Products Meridian 8' x 12' Gable 16698, Инструкция по сборке

Результаты поиска

Содержание Meridian 8' x 12' Gable 16698

Отзывы:

Похожие инструкции для Meridian 8' x 12' Gable 16698

Бренды по названию

Популярные бренды