ABSCO SHEDS CYC4560 Скачать руководство пользователя страница 1

Страница: 1 / 27

PAGE 1

ABSCO INDUSTRIES

ASSEMBLY INSTRUCTION - MODEL: CYC4560 CYCLONE KIT 31/05/13

ASSEMBLY INSTRUCTIONS

CYC4560 CYCLONE KIT

We thank you for choosing an Australian Made Shed. For further assistance please
visit our detailed instructional video library at

Http://www.abscosheds.com.au/watch-videos

At ABSCO Industries we are always looking to be number ONE, so please let us

know what you think of our instructions. Feedback makes us better.

[email protected]

CYC4560 CYCLONE KIT - SUITABLE FOR
LARGE SIZE ABSCO SHEDS UP TO
3M X 4.5M
2.3M X 4.5M
3M X 6M

THE ADDITION OF THIS CYCLONE KIT WILL

INCREASE THE WIND STRENGTH OF YOUR

ABSCO SHED TO THESE CLASSIFICATIONS

W50C (C2) TO WITHSTAND WIND GUSTS OF

UP TO 180KLM/HOUR IF INSTALLED IN

ACCORDANCE WITH THIS ABSCO
ASSEMBLY INSTRUCTION.

WARNING: THE SHED MUST BE ANCHORED TO A 100mm THICK CONCRETE

SLAB AS DETAILED IN THIS INSTRUCTION WITH THE CONCRETE ANCHORS
SUPPLIED, OTHERWISE, EVEN AFTER THE ADDITION OF THE CYCLONE KIT,
THE SHED WILL NOT REACH THE STRUCTURAL ADEQUACY REQUIRED

DURING SEVERE STORMS OR A CYCLONIC EVENT.

WARNING: THE DOOR(S) MUST REMAIN CLOSED WITH ALL PADBOLTS

PROPERLY SECURED DURING SEVERE STORMS OR CYCLONIC EVENT.

READ THESE INSTRUCTIONS
CAREFULLY AND FULLY SO THAT

AN UNDERSTANDING OF THE STEPS

INVOLVED IN CONSTRUCTION IS
OBTAINED. DO THIS WITH
CONSTANT REFERENCE TO
ENGINEERING DRAWINGS
PROVIDED.

MEASURE AND CHECK OFF

ALL THE COMPONENTS PRIOR
TO COMMENCEMENT. IF A

DISCREPANCY IS DISCOVERED,
CONTACT ABSCO INDUSTRIES
IMMEDIATELY FOR ASSISTANCE

6.0m X 3.0m
UTILITY SHED

Содержание CYC4560




























Результаты поиска

Содержание CYC4560

Отзывы:

Похожие инструкции для CYC4560

Бренды по названию

Популярные бренды

ABSCO SHEDS CYC4560, Руководство по сборке

Результаты поиска

Содержание CYC4560

Отзывы:

Похожие инструкции для CYC4560

Бренды по названию

Популярные бренды