H&S HD, Руководство оператора / Каталог запасных частей

Страница: 39 / 54

VARIABLE SPEED BELT ADJUSTMENT
ADJUSTMENT
You should rarely have to adjust the variable speed
drive belt. If, however, it becomes necessary to adjust
the belt, follow the steps listed below:
1. Remove belt as previously instructed.
2. Move control lever to the highest apron speed
position.
3. Check upper sheaves (A), if base of sheaves are
not tight together, it is necessary to adjust.
4. Remove bolt from control rod (B).
5. Slide sheaves tight together, being sure control
yoke (C) is tight against thrust bearing and
sheaves.
6. Adjust control rod (B) so hole in control yoke and
rod align, then one additional turn.
7. Replace bolt. Allow sufficient play when tightening,
so control rod pivots.
8. Place control lever in beater disengage position
and replace belt.
A
B
LUBRICATION GUIDE
-16-
OIL
LEVEL
OIL
LEVEL
The operator should become familiar with all lubrica-
tion points and establish a systematic routine to insure
complete and quick lubrication of the machine.
GEAR BOXES – Before using your new machine,
check the oil in the main apron drive and beater drive
gear box. Keep the main apron gear box filled to the oil
level plug in cover of gear box. Beater drive gear box
should be filled to the center of the shafts. Use 80W-90
gear lube.
DRIVE CHAINS – Lubricate the drive chains with a
light machine oil. Keep chains aligned with sprockets.
This will lengthen the life of the sprockets and chain.
Lubricate chains often.
C
ITEM PART NO. DESCRIPTION
1. S364 Shifter Handle
2. X43 Cotter Pin
3. S91 Shifting Pipe Bracket
4. S360 Speed Selector Panel
5. S365 Front Center Angle
6. S366 Shifting Pipe (Apron)
7. S367 Shifting Rod (Beater)
8. S96 Shifting Bracket
9. S97 Stationary Sheave
10. S295 Sliding Sheave
11. S99 O-Ring
12. S100 Thrust Bearing
13. S101 #40 Chain 5 Pitch
14. S102 #40 Connector Link
15. S103 Linkage Rod
16. S104 Adjustment Block
17. S105 Variable Speed Shifter
18. R10 1/2’’ x 1-1/4’’ Bolt GR.5
19. S106 5/16’’ x 2-3/4’’ Expansion Pin
20. S296 Sheave Pin
21. S108 Variable Speed Belt
22. S109 Spring
23. S110 1/4’’ x 2’’ Expansion Pin
24. S111 Spring
25. 9S17 1/2’’ Lock Nut
26. S285 Beater Clutch Washer
27. S112 Beater Clutch Bracket
28. S113 Beater Clutch Long Arm
29. S114 Beater Clutch Short Arm
30. ST58 Clutch Yoke
31. S115 Beater Clutch Pin
32. S116 Beater Clutch Sprocket
33. S117 Beater Clutch Bushing
34. S118 Beater Shield Top
35. S119 Beater Side Shield
36. S120 Main Side Shield
37. D58 Shield Angle
NOTE: * (Means Not Shown)
ITEM PART NO. DESCRIPTION
38. ST40 Side Shield Bottom
39. S122 Clip Pin Cable
40. F32 U-Bolt
41. S123 Shield Latch Bracket
42. S234 Shield Brace
43. F56 Clip Pin
44. ST86 Front Upright Shield
45. S334 Front Shield
46. X192 Front Shield Latch (Rubber)
47. X193 Latch Catch Bracket
48. X194 Latch Mounting Bracket
49. X195 Pin
50. S359 Plastic Edging 38’’
51. X111 Bolt 3/8’’ x 1’’ GR.5
52. S131 PTO Rubber Shield
53. S221 Spring Shift Bracket
54. S222 Shifting Spring
55. S220 Shifting Spring Rod
56. K94 Spacer
57. T16 1/4’’ Flat Washer
58. S97 Sheave
59. S296 Sheave Pin
60. ST45 Inside Shield
61. ST39 Lower Side Shield
62. S290 Shifter Pipe Handle End
63. S291 Spring Pin Collar
64. S292 Spring
65. S293 Spring Collar
66. 4C9 Lock Collar
67. K92 Snap Ring
68. K90 Bearing
69. 17G141 Bolt 3/8’’ x 1-1/4’’ GR.5
70. S346 Light Bracket
71. BFR319 I-Bolt
72. S328 Edging 3-1/2’’
73. S403 Handle Grip
* S368 Complete Shifter
-3 7 -
FIGURE 4
SHIELDS - BEATER CLUTCH - BELT DRIVE