manualshive.com logo in svg

Handiquilter HQ Sweet Sixteen, Руководство по обслуживанию

Поделиться
Скачать
Handiquilter HQ Sweet Sixteen Скачать руководство пользователя страница 5

HandiQuilter.com

 Page 5

Assembly Torque Specifications

The Torque Specifications apply to all internal and external fasteners in sizes 4.0, 5.0 and 6.0 mm in general 
at ISO 4762 Screw class 8.8. The torque specifications are also generally classified as soft-jointed and are 
listed according to size and placement in the machine.

1.  4 mm Allen socket head cap screws, Class 8.8 @ 2.5 Nm (Uses 3 mm Allen tool)

     • Head-frame, bearing retainers, front cover small

2.  4 mm Allen set screw, class 8.8 @ 1.2 Nm (Uses 2.0 mm Allen tool)

     • Tension assembly, three-hole thread guide, motor pulley, hook

3.  5 mm Allen socket head cap screw class 8.8@ 5.6 Nm (Uses 4 mm Allen tool)

     • Front cover large
     • Belt tensioner
     • Drive-train bracket

4.  5 mm Allen set screw, Class 8.8 @ 2.4 Nm (Uses 2.5 mm Allen tool)

     • Main-shaft timing pulley, hook-shaft timing pulley, collar

5.  6 mm Allen socket-head cap screws Class 8.8 @ 9.9 Nm. (Uses 5 mm Allen tool)
     An exception must be observed here since the screws are considered soft-jointed and shallow-threaded and  
     are used externally. It is therefore advised that this torque specification not exceed 6 Nm.

     • Base plates

6.  6 mm Allen set screw, Class 8.8@ 4.5 Nm (Uses a 3 mm Allen tool)

     • Hand wheel

Содержание HQ Sweet Sixteen










































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды