Handicare TROPHY 20 страница 66 Скачать руководство пользователя

Страница: 66 / 99

Trophy 20

66 | Service instructions

Replacing the stop switch

Preparation

• Switch off the scooter with the ignition key.
• Disconnect the batteries.

Instructions

The following operations are required to replace the stop
switch:

Note!

Suitable work area required!

• Remove the basket and the mounting bracket for the

mirrors.

• Remove the two bolts and remove the front tiller cover.
• Remove the nut, the four Ejot screws and the

dashboard.

•  Disconnect all connectors from the tiller PCB.
•  Remove the three Ejot screws to remove the tiller PCB.
•  Remove the two recessed button head screws to

remove the console bottom.

• Disconnect the connectors of the console bottom.
• Remove the recessed button head and Ejot screws,

disconnect the connectors the stop switch and remove
the top and bottom steering wheel covers.

• Mount the new stop switch.
• Rebuild the scooter in the reverse order.

Relevant article numbers

• 9006138 Emergency stop

Tools used

• Socket, 10 mm
• Screwdriver,

crosshead

Notice

• Make sure the scooter is switched off.

Содержание TROPHY 20




































































































Результаты поиска

Содержание TROPHY 20

Отзывы:

Похожие инструкции для TROPHY 20

Бренды по названию

Популярные бренды

Handicare TROPHY 20, Руководство по обслуживанию

Результаты поиска

Содержание TROPHY 20

Отзывы:

Похожие инструкции для TROPHY 20

Бренды по названию

Популярные бренды