Handicare TROPHY 20 Скачать руководство пользователя страница 61

Страница: 61 / 99

Service instructions | 61

Trophy 20

Service instructions | 61

Replacing the gas spring

Preparation

• Switch off the scooter with the ignition key.

Instructions

The following operations are required to replace the gas
spring:

Note!

Suitable work area required!

• Remove the basket, the mounting bracket for the

mirrors, the front cover and the front cover rear part.

• Pull the handle for steering adjustment upwards and

move the steering column downwards.

• Remove the four hinge pins and the spiral pin.
• Disconnect the gas spring actuator, remove the hinge

pin and remove the two bolts from the gas spring slider.

• Remove the gas spring slider and loosen the hinge pin

and lock nut.

• Mount the new gas spring.
• Rebuild the scooter in the reverse order.

• Note!

Be sure you fasten all bolts and nuts with the

correct torque!

Relevant article numbers

• 9007359 Gas spring 300N

Tools used

• Socket, 7 mm / 8 mm / 10 mm / 13 mm
• Screwdriver,

crosshead

• Hammer

(plastic)

• Chaser
• Loctite

243

Notice

• N.a.

Содержание TROPHY 20




































































































Результаты поиска

Содержание TROPHY 20

Отзывы:

Бренды по названию

Популярные бренды

Handicare TROPHY 20, Руководство по обслуживанию

Результаты поиска

Содержание TROPHY 20

Отзывы:

Бренды по названию

Популярные бренды