Hanbell RTM-090 Скачать руководство пользователя страница 32

Страница: 32 / 39

[文件標題]

[日期]

Length (mm)

105

Width (mm)

155

Height (mm)

Weight (kg)

0.25

IP protection degree (*For storage, IP 2X or higher level is
required)

IP 00(Body)

Operation Temp. (

℃

)

+5~+40

℃

Relative humidity (%)

30%~70%

Storage Temp. (

℃

)

-25

℃

~+55

℃

Power

24 VDC

5.7 THD installation & fix

※

The THD board is provided mounted on a RS100 support. The THD board must be mounted in the

upright position on DIN rail as figure 5.2.

※

The THD board must be installed with proper space away from cable tray.

※

High voltages are presented on the THD board. It is suggested to install plexiglass cover.

※

The link between the THD board (power supply 24Vdc) and MBC must be carried out with a

twisted wires.

Figure 5.2 THD installation

Extrude THD board
until it is locked

Содержание RTM-090




































Результаты поиска

Содержание RTM-090

Отзывы:

Похожие инструкции для RTM-090

Бренды по названию

Популярные бренды

Hanbell RTM-090, Руководство пользователя

Результаты поиска

Содержание RTM-090

Отзывы:

Похожие инструкции для RTM-090

Бренды по названию

Популярные бренды