manualshive.com logo in svg

Hanbell RTM-090, Руководство пользователя, Страница: 3 / 39

Поделиться
Скачать
Hanbell RTM-090 Скачать руководство пользователя страница 3

[文件標題] 

[日期] 

 

 

 

 

 

 

3 

Vol. 1.2 © 2020 Hanbell Precise Machinery Co., Ltd. 

All rights reserved 

 

4.4.3 Grounding ............................................................................................................................................. 24

 

4.4.4 Cable of main power input .................................................................................................................... 25

 

4.4.5 Connection notice ................................................................................................................................. 26

 

4.5 MCC (Maximum Continuous Current) of motor......................................................................................... 26

 

5. Control line connection ..................................................................................................................................... 27

 

5.1 Magnetic Bearing Controller (MBC) info ................................................................................................... 28

 

5.2 MBC installation notice ............................................................................................................................... 28

 

5.4 MBC connection port .................................................................................................................................. 30

 

5.5 MBC connection data .................................................................................................................................. 31

 

5.5.1 Additional info. about connection port ................................................................................................. 31

 

5.5.2 Communication of MBC and PLC ....................................................................................................... 31

 

5.6 Total Harmonic Distortion (THD) info. ...................................................................................................... 31

 

5.7 THD installation & fix ................................................................................................................................. 32

 

5.8 THD connector ............................................................................................................................................ 33

 

5.9 Variable Frequency Drive (VFD) Connector .............................................................................................. 34

 

5.10 Parameter of inverter ................................................................................................................................. 34

 

6. Compressor lifting and installation .................................................................................................................... 35

 

6.1 Compressor lifting ....................................................................................................................................... 35

 

6.2 Compressor installation ............................................................................................................................... 35

 

7. Instructions ........................................................................................................................................................ 37

 

7.1 Accessories .................................................................................................................................................. 37

 

7.2 Valves .......................................................................................................................................................... 37

 

7.3 Testing before power supply ....................................................................................................................... 37

 

7.4 System requirement ..................................................................................................................................... 38

 

7.5 Control requirement ..................................................................................................................................... 38

 

7.6 Others .......................................................................................................................................................... 38

 

 

Содержание RTM-090








































Отзывы:

Нет отзывов