manualshive.com logo in svg

Hamworthy FLEET Series, Инструкция по установке, вводу в эксплуатацию и эксплуатации

Hamworthy FLEET Series - Руководство по монтажу, вводу в эксплуатацию и эксплуатации. Здесь вы можете бесплатно скачать инструкцию по использованию. Посетите {веб-сайт}, чтобы получить доступ к руководству пользователя. Идеальное решение для установки и эксплуатации вашего оборудования.

Поделиться
Скачать
background image

 

HAMWORTHY HEATING LTD 

 

66 

FLEET W series 

 

500001211/F 

 

 

vent pipe must rise continually, any valve fitted between a boiler and the open vent pipe for maintenance 
purposes shall be of the 3 way type such that when closed to the vent pipe the boiler will be open to atmosphere. 
The vent pipe shall be protected against freezing where this might occur. See BS 6644 for detailed information on 
Open Vent and Cold Feed Pipes.

 

 

E1.5 Thermometer 

 

A thermometer complete with pocket should be fitted in the pipe work to indicate water flow temperature. See 
Figure E1.1.1 for typical position. 

 

E1.6 Drain Valves 

 

Each boiler has a 15mm NB drain valve fitted in the boiler return,  for draining the boiler only. The heating system 
in total should have drain valves as recommended by BS 6644. See Figure E1.1.1 for typical position. 

 

E1.7 Circulating Pump 

 

Each individual boiler is fitted with an integral circulating pump ensuring flow through the boiler and primary circuit. To 
ensure the correct flow through the boiler, there is a balancing valve fitted to the flow pipe within the boiler. This is factory 
set and must not be adjusted. 
One or more circulating pumps will be required to circulate water around the heating system. All pumps should be 
sited to facilitate servicing. It is important that when Fleet

 

boilers are used to replace boilers on an existing 

system, the system design must be modified acknowledging the performance of the integral circulating pump.. It is 
also important that the existing system be flushed through twice to remove any loose matter which may have 
accumulated. To protect the boiler heat exchanger, it is strongly recommended that a dirt/air separator is fitted in 
the return to the boiler. If in any doubt regarding the cleanliness of the system, a coarse filter should be fitted in 
the return pipe work to the boilers. 

E1.8 Minimum Water Flow Rates 

 

Minimum water flow rates are shown in table at beginning of Appendix E. These flow rates should be maintained 
through the boiler at all times whilst the boiler is firing. To prevent the boiler firing in the event of poor or no flow, 
the boiler is fitted with an integral flow switch. Particular attention should be paid to the restriction of external flow 
circuits during periods of low heat demand. 
Each boiler module is fitted with a flow balancing valve on the return pipe within the unit. This valve may require 
adjustment to ensure the correct flow through the boiler - refer to commissioning instructions Section  7.7 

 

E1.9 Waterside Pressure Drop 

 

The waterside hydraulic resistance (Pressure drop) is given in table at beginning of Appendix E. 

 

E1.10 Water Flow Controls 

 

The Fleet boiler is fitted with an integral circulating pump, which will shut off circulation 5 minutes after the boiler 
has ceased firing. 
Any external mixing valve / shunt pump or similar controls MUST always ensure that the minimum water flow rate 
as given in table at beginning of Appendix E is maintained. As a precaution, the Fleet boiler is fitted with a flow 
switch. The flow switch is designed to operate such that the boiler will shut down if insufficient flow occurs. 

 

E1.11 Frost Protection 

 

Consideration should be given to fitting an optional outside air sensor, to provide the necessary frost protection. 

 

E1.12 Unvented Systems 

 

Refer to Figure E1.1.1 on opposite page for typical layout of an unvented (Pressurised) Hot Water System. For 
system design refer to BS 7074 Part 2. In order to correctly size a pressurisation unit for any heating system the 
following parameters are required. 

1) 

Static height of highest component in system (metres) 

2) 

System volume. If this is not known, a general rule of thumb of 10litres/kW of installed boiler power 
can be used. 

3) 

Maximum flow temperature (°C) 

4) 

Maximum system hot working pressure, generally given in bar gauge. 

From the parameters given, Hamworthy Heating can size the pressurisation unit and also the expansion vessel. 
Care must be taken in sizing expansion vessels to ensure maximum acceptance factors are not exceeded. 
Normally manufacturers of vessels impose a limit of 0.5. This value must not be exceeded at any time during the 
operation of the boiler, this includes the over pressure condition should a safety valve lift. 
Consideration should also be given to sizing of the safety valve(s) in the system. Refer to BS 6759: Part 1 for 
further information and to BS 6880: Part 1 for design considerations. 

Содержание FLEET Series



















































































Отзывы:

Нет отзывов

Похожие инструкции для FLEET Series

Laars JVS Installation And Operation Instructions Manual preview
JVS
Бренд: Laars Страницы: 36
Radiant R1C 34/B Instructions For Installation, Use And Maintenance Manual preview
R1C 34/B
Бренд: Radiant Страницы: 72
Vaillant ecoTEC plus 938 Installation And Maintenance Instructions Manual preview
ecoTEC plus 938
Бренд: Vaillant Страницы: 72
Lochinvar 000 BTU/HR User'S Information Manual preview
000 BTU/HR
Бренд: Lochinvar Страницы: 12
abc COMBO 25 Instructions For Use Manual preview
COMBO 25
Бренд: abc Страницы: 23
Aerco MFC 10000 User Manual preview
MFC 10000
Бренд: Aerco Страницы: 170
Aerco Benchmark 1500 User Manual preview
Benchmark 1500
Бренд: Aerco Страницы: 186
THERMO 2000 VoltMax105 Installation And Operation Manual preview
VoltMax105
Бренд: THERMO 2000 Страницы: 60
Wood Stone MT. OLYMPUS WS-SFR Installation And Operation Manual preview
MT. OLYMPUS WS-SFR
Бренд: Wood Stone Страницы: 21
Raytherm 133-4001 Installation & Operating Instructions Manual preview
133-4001
Бренд: Raytherm Страницы: 44
Hermann Eura Condensing Installation, User And Servicing Instructions preview
Eura Condensing
Бренд: Hermann Страницы: 60
E.C.A. Proteus Premix PPR 14 HCH Installation And User'S Operating Instructions preview
Proteus Premix PPR 14 HCH
Бренд: E.C.A. Страницы: 42
ACV Compact A Product Catalogue preview
Compact A
Бренд: ACV Страницы: 27
Knight 285 Service Manual preview
285
Бренд: Knight Страницы: 44
Ideal Boilers Procombi Exclusive 24 Installation & Servicing Instructions Manual preview
Procombi Exclusive 24
Бренд: Ideal Boilers Страницы: 72
Ideal Boilers Classic LX RS 230 User Instructions preview
Classic LX RS 230
Бренд: Ideal Boilers Страницы: 4
U.S. Boiler Company V13A RO/FO Installation, Operating And Service Instructions preview
V13A RO/FO
Бренд: U.S. Boiler Company Страницы: 48
Radiant RK 25/B User Manual preview
RK 25/B
Бренд: Radiant Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды