HAMPTON BAY H35U-LP, Инструкция для владельца и по установке

Страница: 13 / 60

Hampton® H35U Direct Vent Freestanding Gas Stove
13
installation
General Safety Information
1) The appliance installation must conform with
local Canadian Electrical Code.
2)
The appliance when installed, must be electri-
cally grounded in accordance with local codes,
or in the absence of local codes with the cur-
rent National Electrical Code, ANSI/NFPA 70
or CSA C22.1 Canadian Electrical Code.
3) The appliance should be inspected for shipping
damage before use and serviced annually by
a professional service person
. More frequent
cleaning may be required due to excessive
lint from carpeting, bedding material, etc. It
is imperative that control compartments, and
circulating air passageways of the appliance
be kept clean and free from excessive lint from
carpeting.
4) See general construction and assembly in-
structions. The appliance and vent should be
enclosed when installed in or passing through
a living area, where children may come in
contact with it.
5) This appliance must be connected to the speci-
fied vent and termination cap to the outside
of the building envelope. Never vent to
another room or inside a building. Make sure
that the vent is fitted as per the instructions
starting in the "Exterior Vent Terminal Loca-
tions" section.
6)
Inspect the venting system annually for block-
age and any signs of deterioration.
7)
Venting terminals shall not be recessed into a
wall or siding.
8) Any safety glass removed for servicing must
be replaced prior to operating the appliance.
9) To prevent injury, do not allow anyone who
is unfamiliar with the operation to use the
fireplace.
Installation Checklist
1)
Locate your appliance. Refer to the following
sections:
a. Clearances to combustibles
b. Locating Your Gas Stove
c. For venting requirements, see "Venting
Introduction" to "Venting Arrangements"
Section.
2) Install Optional Fan. Refer to the "Optional Fan
Installation" section.
3)
Set vent restrictors. Refer to the "Vent Restrictor
Position" section.
4) Install venting. Refer to the following sections
where applicable:
a. Check all venting requirements.
See "Venting Introduction" to "Venting
Arrangements" sections.
b. Vertical Termination with Co-linear Flex
System
c. DV Stove Horizontal Vent Kit
d. Dura-Vent Termination Kit.
5) Make gas connections. Refer to the "Gas Con-
nection" section
Test the pilot. Must be as per diagram in the
"Maintenance Instruction" section.
If converting to Propane, make changes prior
see the "Conversion from Natural Gas to Pro-
pane" section.
6) Test Gas Pressure. Refer to the "Gas Pipe
Pressure Testing" section.
7) Install standard and optional features. Refer
to the following sections where applicable:
a. Brick Panels
b. Log Set Installation
c. Wall Thermostat
d. Remote Control
8) Final check. Refer to the "Final Check" section.
Before leaving this unit with the customer, the
installer must ensure that the appliance is fir-
ing correctly and
operation fully explained
to customer .
This includes:
1)
Clocking the appliance to ensure the correct
firing rate (rate noted on label) after burning
appliance for 15 minutes.
2) If required, adjusting the primary air to ensure
that the flame does not carbon. First allow the
unit to burn for 15-20 min. to stabilize.
CAUTION: Any alteration to the product that
causes sooting or carboning that results in
damage is not the responsibility of the manu-
facturer.
Clearances to Combustibles
The clearances listed are MINIMUM distances.
Measure the clearance to both the appliance and
the chimney connector.
The farthest distance is
correct if the two clearances do not coincide.
For example, if the appliance is set as indicated in
one of the figures but the connector is too close,
move the stove until the correct clearance to the
connector is obtained.
This appliance may be installed only with the
clearances as shown in the situations pictured.
Do not combine clearances from one type of
installation with another in order to achieve
closer clearances.
This unit can be installed on a solid combustible
surface like a wood floor. This unit can also be
installed directly on carpeting or vinyl.
Use the minimum clearances shown in the dia-
grams below:
H35U Clearances
A Side Wall to Unit 6-1/2" / 165mm
B Back Wall to Unit 6" / 152mm
C Vertical Vent Pipe to Back Wall
2" / 50mm
E Unit Corner to Wall 2" / 50mm
Unit Top to Alcove Ceiling 36" / 914mm
Minimum ceiling height is 36" / 914mm from top
of unit.
Emissions from burning wood or gas could
contain chemicals known to the State of
California to cause cancer, birth defects or
other reproductive harm.