Hammond A-162, Руководство пользователя

Страница: 66 / 122

 Owner’s Manual
66
CONTROL
In this mode, you can adjust the settings of each controller.
You may change the functions of several of the playing controls of
the organ. Also, on the underside of the key bed is a jack for con-
necting the foot switch. You can select how a connected foot switch
or CU-1 (half-moon Leslie switch) will function in this mode.
To locate this mode:
1. From either of the PLAY screens, touch the [MENU/EXIT] but-
ton. Menu A will display.
2. Touch the [4] CONTROL button.

FOOT SWITCH
FOOT SWITCH 1 - MODE (G)
Th is is for setting the function of the Foot Switch on the Expression Pedal.
OFF: No function.
LESLIE S/F ALT, MOM, TRI:
These are for switching SLOW/FAST of the Leslie eff ect.
At ALT, SLOW/FAST is alternately switched at each press of the Foot Switch, and at TRI, the
Leslie rotors are switched OFF if the switch is held longer than 1 second..
At MOM, The Leslie rotors run FAST when the switch is pressed and held. Release the
switch and the Leslie rotors run SLOW.
GLIDE:
Pressing the foot switch will cause the pitch to be lowered. The amount that the pitch is
lowered is determined by a parameter setting (P. 67 #11 to 13).
DAMPER SWELL, GREAT, PEDAL:
Pressing and holding the foot switch while notes are pressed on SWELL, GREAT or PEDAL
causes the notes to be sustained for as long as the foot switch is held. This function is
similar to the damper pedal on a grand piano.
PRESET FWD, REV:
Pressing and releasing the foot switch will advance (FWD) or go backward (REV) through
the SWELL Manual Presets.
SPRING:
Pressing and releasing the foot switch will produce a “spring shock” eff ect similar to the
“gunshot” eff ect produced when a spring reverb unit is shaken or jostled.
DELAY TIME:
This function allows you to set the Delay Time of the Reverb eff ect (P. 66 #4) with the Foot
Switch. For example, if you press and release the Foot Switch once, then press and release
it again 0.2 seconds later, the delay time will be 0.2 seconds. You can then silence the
Delay eff ect by pressing and holding the Foot Switch.
FOOT SWITCH 2 - DEVICE (G)
Th is is for selecting which equipment is connected to the Foot Switch 2 jack.
PEDAL: for Foot Switch.
CU-1: for the Leslie Switch CU-1 (= optional).
FOOT SWITCH 2 - TIP MODE (G)
Th is is for setting the Foot Switch 2 jack.
TIP AND RING
TRS is an acronym for T ip- R ing- S leeve, and refers
to the fact that a connecting plug can have more
than one connector. This means that more than
one Foot Switch can be connected, thereby allow-
ing you to control more than one function using
the same Foot Switch jack.
If you wish to do this, you will need a Stereo Adapt-
er which has a Stereo plug and two (2) Mono jacks.
Insert the Stereo plug into the FOOT SW jack and
connect a Foot Switch to each of the Mono input
jacks. In most cases, the
Left (L) input jack will ac-
cess the Tip function while the Right (R) will access
the Ring function.
DAMPER
The word “Damper” comes from the damper pedal
of the piano.
It is also referred to as a “Sustain” pedal. Notes are
held as long as the pedal is depressed.
SPRING REVERB
When an old-style Spring Reverb unit was shaken
or bumped, the springs would strike the inside
of their enclosure, resulting in a loud “bang.” This
sound has been used as an artistic eff ect in several
styles of contemporary music. The SPRING setting
replicates this eff ect.
Tip
Ring
Sleeve