manualshive.com logo in svg

Hamilton Sundstrand Company Gas Fuel Metering Valve HFG2.0, Руководство пользователя

Поделиться
Скачать
Hamilton Sundstrand Company Gas Fuel Metering Valve HFG2.0 Скачать руководство пользователя страница 36

 

30

 HFG2.0 

USER 

GUIDE

 

 

 Note:

 The MCE analog and discrete signal interfaces are 

electrically isolated. The serial communication interface is 
optically isolated 

  

2.3  Mechanical Description 

The HFG2.0 consists of two main parts, an actuator and a valve 
assembly. 

 

Actuator 

The actuator is the primary drive mechanism for the valve assembly. The 
actuator portion of the HFG2.0 consists of four main assemblies: 

•

  Main Housing Assembly 

•

  Brushless DC Motor Assembly 

•

 Resolver 

Assembly 

•

 Linear 

Drive 

Mechanism 

 

Main Housing Assembly 

The main housing assembly consists of the main housing, motor cover, 
extension-rod bearing, and associated seals. The main housing assembly 
is the primary structural system component and supports all the bearings, 
motor cover, mountings, and connectors. It also provides explosion-proof 
containment. 

The housing is fitted with a stainless steel liner to provide thermal and 
dimensional stability for the main bearing. This liner is permanently 
installed into the aluminum main housing. A retaining ring is included for 
redundant retention. 

The main housing also contains rigid mechanical stops to prevent 
extension rod travel beyond the design specification. See Figure 2-2. 

Brushless DC Motor Assembly 

A brushless DC motor powers the HFG2.0 linear drive mechanism. The 
DC motor consists of a stator and rotor. See Figure 2-2. 

Motor Stator 

The motor stator is attached to the main housing by a pre-loaded wave 
spring and screws. Thermistors are embedded in the stator windings to 

Содержание Gas Fuel Metering Valve HFG2.0







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды