manualshive.com logo in svg

Hamilton Sundstrand Company Gas Fuel Metering Valve HFG2.0, Руководство пользователя

Поделиться
Скачать
Hamilton Sundstrand Company Gas Fuel Metering Valve HFG2.0 Скачать руководство пользователя страница 11

 

 

 

Figure 1-1.  Typical HFG2.0 Gas Fuel System Installation 

 

 

Figure 1-2.  Alternate HFG2.0 Gas Fuel System Installation 

 

Dimensions 

Figure 1-3 and Figure 1-4 show external dimensions for the 3-piece 
housing and 1-piece housing versions of the HFG2.0, respectively. 

 

Mounting Considerations 

The HFG2.0 can be mounted directly to a gas turbine engine skid using 
brackets provided by the engine manufacturer. The HFG2.0 can be 
mounted with any directional orientation, whether horizontal, vertical, or at 
an angle. The clevis must be supported if the HFG2.0 is mounted 
horizontally. 

Valve life can be maximized if the HFG2.0 is mounted with the vertical 
orientation shown in Figure 1-3 or Figure 1-4, where the valve end is on 
the bottom. The drain hole is most effective when mounted in this vertical 
orientation.  

Note:

 The one-piece housing version of the HFG2.0 does not 

have a drain hole. 

 

INSTALLING THE HFG2.0 

5

 

Содержание Gas Fuel Metering Valve HFG2.0







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды