manualshive.com logo in svg

Hamilton Sundstrand Company Gas Fuel Metering Valve HFG2.0, Руководство пользователя

Поделиться
Скачать
Hamilton Sundstrand Company Gas Fuel Metering Valve HFG2.0 Скачать руководство пользователя страница 28

 

22

 HFG2.0 

USER 

GUIDE

 

 

FUNCTION 

Standard 9-Pin 

COM Port 

Standard 25-Pin 

COM Port 

Transmit  (Tx). 

Pin 3 

Pin 2 

Receive  (Rx) 

Pin 2 

Pin 3 

Ground  (GND) 

Pin 5 

Pin 7 

Table 1-5.  Computer COM Port Pin Outs 

WARNING 

Property Damage Hazard – The serial inputs are not electrically 
isolated 

. Failure to properly isolate the user serial interface 

could result in actuator or computer damage.  Use separate 
conduits for power and signal wiring. Close proximity to power lines 
may cause signal interference. 

Shock Hazard – The serial inputs are not electrically isolated 

. 

If the power input is floating (not grounded), the serial input 
connections may have up to 120 VDC present. 

Property Damage Hazard – DO NOT connect 24 VDC power to any of 
the serial interface connections. 

 

Note:

 The pin designations shown in Table 1-5 are for the COM 

port on the 

computer

. Make sure that the wiring to the 

COM port mating connector correctly matches Transmit 
from the HFG2.0 to Receive on the computer’s COM port, 
and vice versa. 

Note:

 The maximum distance for serial connections is 50 ft. This 

will typically only allow for local interface with a laptop PC.  

Note:

 The serial interface connections are not isolated

. 

Isolation must be provided when connecting to a computer.  

Содержание Gas Fuel Metering Valve HFG2.0







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды