12
13
AND 3 BUTTONS ON THE REAR SIDE
1. [ °C/°F ]
Toggle the temperature unit °C <- -> °F
2. [ UNIT ]
Press to toggle the pressure unit. (hPa/mb -> inHg)
3. [ MODE ]
Press & hold 2 seconds to enter backlight color setting
mode.
SLIDE SWITCH [ BACKLIGHT ] ON THE REAR SIDE TO
SELECT THE BACKLIGHT MODE
Power Supply
Slide
switch
position
Battery
Only
Battery
& Adapter
Adapter
only
Auto
Wave hand in front of the
IR sensor to activate backlight
for 5 seconds
OFF
Disable the backlight function
ON
Wave hand
in front
of the IR
sensor to
activate
backlight
for
5 seconds
Backlight always on
GETTING STARTED
This Weather Station was designed for easy set up.
For best operation, the following steps are required to be
done in the proper sequence.
1.
Insert batteries for main unit before doing so for the
sensor units.
2.
Receiving unit cannot be set manually until the wire-
less remote sensor unit registration procedure has
been completed.
3.
Position the remote unit and main unit within effective
transmission range, which, in usual circumstances,
is 250 feet.
Although the remote unit is weather resistant, it should
be placed away from direct sunlight, rain or snow.
BATTERY INSTALLATION FOR MAIN UNIT
1.
Turn the metal nut anti-clockwise on the bottom of the
unit to open and release the battery compartment;
2.
Insert 4 AA size 1.5 V alkaline battery as indicate by the
polarity;
3.
Push the battery compartment back, turn the metal nut
clockwise to lock;
NOTE:
Replace the batteries when the low battery indi-
cator appears on the top-right corner of the LCD.
WIRELESS REMOTE SENSOR REGISTRATION
PROCEDURE
1.
Insert x4 AA batteries fi rst to the main unit, the outdoor
temperature display shows “- -” . – While the wave
icon will keep blinking for 2 minutes indicate unit is in
sensor searching mode.
2.
In a second step, insert the x2 AAA batteries for
the sensor unit. The LED on the front panel will start
fl ashing at a rate of one time per around 2 seconds
indicates channel-1 is in use.
3.
While the LED in the sensor unit is fl ashing, press once
the [ CH ] key will change the sensor channel setting
to 2. Keep toggle on [ CH ] key can change channel
setting up to 5. The LED is blinking at a frequency to
indicate the channel setting. i.e. continuous blinks
2 times indicate channel-2 is selected.
NOTE:
If user does not press any key for 10 seconds,
it will exit the channel setting mode and transmit
the RF signal. The main unit will register the
temperature reading.
(If the transmitter has the LCD display, the °C/°F key will
toggle the temperature unit on the LCD.)
REMOTE CHANNEL AUTO-SCROLLING
This device is equipped with an auto-scroll function.
While the auto-scroll function is set, the unit will
automatically cycle to display temperature of each
remote sensor for 6 seconds.
1.
To retrieve manually the specifi c sensor temperature
reading, press CHANNEL key until desired channel
number is displayed.
2.
To enable auto-scroll function, use CHANNEL button to
select channel 1, 2, ... until auto scroll icon appears on
the left hand corner of the 3rd line display.
H. Auto scroll indicator
The animated rolling arrow icon is shown to indicate
the auto scroll of 5 different remote channel.
I. Outdoor maximum/minimum indicator
Indicates the maximum/minimum outdoor temperature
is displayed
J. Remote sensor battery low indicator
Appears when the batteries of the remote sensor are
running dry and the temperature measured by this
sensor is no longer reliable. The user must change the
batteries at once.
K. Barometric history indicator
Indicates the recorded air pressure reading in the past
24 hours
L. Barometric pressure window
Displays the barometric pressure reading in mb hpa or
inHg.
M. Barometric pressure chart
Shows the barometric pressure trend chart for the
past 24 hours
N. Moon phase
The animated running moon phase will pause for
5 seconds in place of current moon phase.
O. Sun position and Moon position
Sun rises from the east (E) and goes down in the west
(W) everyday. This weather station can calculate the
different sunrise, sunset, moonrise and moonset time
according to the input city and diagrams the sun and
moon position in a day at 3 hour interval.
P. Sunrise and Sunset time
Shows the exact sunrise time of a pre-set city in a
specifi c day. Press [ CITY ] button once to toggle to see
the sunset time.
Q. City name
Abbreviation of a city name in Europe. The user must
set to his own located city before start to use this
weather station to have the correct sunrise, sunset
time & moon phase.
R. Clock window
Display current time, current time and weekday, calen-
dar or alarm time
S. Radio reception signal
Indicates the condition of DCF77 radio controlled time
reception
T. Alarm on icon
Appears when alarm is activated
DESCRIPTION OF BUTTONS
Sculpture has 7 major function buttons on the edge
1. [ MEMORY ]
Toggle to view the Max/Min reading of the indoor
temperature/humidity & remote temperature.
Press & hold 2 seconds to clear indoor temperature/
humidity memories or remote temperature records.
2. [ CHANNEL ]
Select among channel 1, 2, 3, 4, 5 or to enter auto
scroll mode.
Press and hold 2 seconds to activate or deactivate the
sensor searching mode.
3. [ HISTORY ]
Press to view the past 24-hour barometric readings.
Press and hold 2 seconds to enter the altitude adjust-
ment mode.
4. [ ]
Press once to increase the date to view the MOON
PHASE status, Sunrise and Sunset time of a specifi c
day in Day-Month-Year (or Month-Day-Year depends
on the date format setting).
Press once to increase the setting in CLOCK, CALEN-
DAR or ALARM setting mode Press & hold 2 seconds
to manually activate or deactivate the radio controlled
function.
5. [
]
Press to decrease the date to view the MOON PHASE
status, Sunrise and Sunset time of a specifi c day in
Day-Month-Year (or Month-Day-Year depends on the
date format setting).
Press once to decrease the setting in CLOCK,
CALENDAR or ALARM setting mode.
Press once to arm or disarm the daily alarm under
alarm display mode.
6. [ CITY ]
Press once to toggle between the sunrise and sunset
time of a pre-set city in a specifi c day.
Press and hold 2 seconds to enter city setting mode,
use [
] and [
] to select the abbreviation country
name and then city name according to the list in the
appendix, press [ CITY ] to confi rm.
Use [
] and [
] to select the DST (Daylight Saving
Time) “ON” or “OFF”, press [ CITY ] to confi rm.
7. [ CLOCK ]
Toggle amongst display for Clock-Sec (HR-MIN-Sec),
Clock-day (HR-MIN-Weekday), Calendar (Date-Month-
Year), alarm time and repeat…
00092651bda.indd 12-13
00092651bda.indd 12-13
19.06.2009 11:09:40 Uhr
19.06.2009 11:09:40 Uhr
