background image

4

ECOVENT Operating Instructions

ECO

V/1

120

12/re

v1/EN

Section 1 – Installation

1.2 Fitting to Oven

 

 

Information:  The ECOVent condensate hood has been designed to fit on

 

 

 

 

Electrolux ovens only, specifically models 269281, 267281, 267280

 

 

 

 

No direct connection to an outgoing extract system is required,

 

 

 

 

as the steam laden air filtered by means of baffle filters, mesh

 

 

 

 

moisture eliminators and perforated cassette.

 

 

Instruction:   1.2.1 Unscrew the 2 No. centre fixing screws, located to the rear

 

 

 

 

of the ovens, that fix the roof panel in place. Screw the fixing bracket (8) 

 

 

 

 

into position using the holes provided.

 

 

 

 

1.2.2. Remove the nuts from the two locating studs fitted to the

 

 

 

 

bottom rear of the condensate hood.

 

 

Safety:  

1.2.3. Carefully lift the condensate hood ( kg) into position, ensuring

 

 

 

 

the locating stud fit into the holes on the fixing bracket. Take care

 

 

 

 

To lift condensate hood clear of the flues exposed on the roof of the

 

 

 

 

oven. Refit nuts and tighten.

 

 

 

 

1.2.4. Check steadiness of unit when condensate hood is lifted on

    combi 

steamer.

 

 

 

 

1.2.5. Condensate hood is not developed for floor standing units.

 

 

 

 

1.2.6. Before connecting the condensate hood ensure the information

 

 

 

 

on the rating plate corresponds.

1.3 Fitting Door Magnet

    Fig 

1.

Содержание ECOV-10











Отзывы: