background image

Page 7

1000001732  (Rev. D - 06/16)

HAC-HB*1B   HAC-HB-NF-*1B

RE-PLUMBING SINGLE STATION WATER CIRCUITS (WITH FILTER)

CAUTION:

• 

This procedure MUST be performed on ALL SINGLE HALSEY TAYLOR WATER COOLERS or the bottle

filling unit 

WILL NOT perform properly!

• 

When disconnecting water lines use a container to catch any water running out of the lines.

FILTER

 HAC HYDROBOOST PLUMBING

1) Connect Water Supply:

• 

Remove the in-line strainer outlet tube from

the Regulator Inlet.

• Remove the 1/4" copper tubing from the

regulator Outlet.

• 

Connect the Filter outlet using 1/4” poly

tubing to the Evaporator 1/4” copper inlet

using the supplied 1/4” union.

2) Add water supply to Bottle Filler:

• 

Cut the Evaporator Outlet 1/4” poly tubing

6” from the Evaporator Outlet and insert

the 1/4” Tee fitting between the two pieces.

• Connect Bottle Filler supply line to Tee fitting.

• Remove 1/4” poly tubing from Bubbler.

3) Re-route water supply to Regulator:

• 

Insert end of 1/4” poly tubing from the Tee fitting

to the Regulator Inlet.  which is marked with

the word “IN” on the Regulator.

4) Connect water supply from Regulator to Bubbler.

• 

Cut a 12” piece of 1/4” poly tube along with

matching length of insulation.

• 

Insert 1/4” poly tube into insulation.

Insert 1/4” poly tube into the Regulator Outlet

(unmarked).

Opposite end of 1/4” poly tube will be Inserted

later into the Bubbler.

Fig. 3

IN-LINE

STRAINER

STANDARD HAC PLUMBING

1/4”UNION

EVAPORATOR 

INLET

EVAPORATOR

 

6” TUBING

TEE

EVAPORATOR 

OUTLET

12” TUBING

REGULATOR

TO BOTTLE 

FILLER

TO BUBBLER

EVAPORATOR

 

EVAPORATOR 

INLET

REGULATOR

EVAPORATOR 

OUTLET

TO BUBBLER

Buy at

| 855-558-9600 | BottleFillingStations.com

Содержание HTHB-HAC
















Отзывы: