Haldex EB+ Gen3 Скачать руководство пользователя страница 42

Страница: 42 / 132

EB+ Gen3

Installation guide

Innovative Vehicle Solutions

2013

Sensor connection

Sensor extension cable socket must be pushed fully
into sensor cable plug till they clip into place to prevent
falling out with axle vibration.

Haldex recommend that all electrical components
are greased prior to assembly using the appropriate
electrical grease.

Where possible use a clip and bracket to secure sensor
cable connection.
The female connector of the sensor cable should
always be horizontal or pointing downward to reduce
the possibility of water ingress.

Alternatively: sensor cable connection to be positioned
on axle or between axle ‘U’ bolts and supported with
cable ties with 50 mm of each end.

Extension cable plug

Sensor cable socket

Clip to ‘click’

Sensor cable

Extension cable

Dirt shield

Connection

assembled into clip

and bracket

Dirt shield

ﬁxing bolts

Axle

‘U’ bolts

Cable tie

Axle

Connection

Hub and drum/

disk assembly

Содержание EB+ Gen3





































































































































Результаты поиска

Содержание EB+ Gen3

Отзывы:

Похожие инструкции для EB+ Gen3

Бренды по названию

Популярные бренды

Haldex EB+ Gen3, Руководство по установке

Результаты поиска

Содержание EB+ Gen3

Отзывы:

Похожие инструкции для EB+ Gen3

Бренды по названию

Популярные бренды