Hainbuch TOPlus mini Скачать руководство пользователя страница 75

Страница: 75 / 120

TOPlus mini / TOPlus premium pull-back
Installation

Order h49 7144.907-333

4. Screw the functional unit firmly home on the machine

drawtube.

WARNING

Serious injuries caused by incorrectly installed
clamping screws being ejected centrifugally!



If the bores for the fixing screws in the spindle
flange are not fully covered by the functional unit,
the clamping screws must always be located be-
tween the bores for the fixing screws in the spin-
dle flange.

5. Turn back the functional unit until the balancing marks

on the spindle flange are aligned with those on the func-
tional unit.

WARNING

Serious crushing injuries caused by improper ma-
chine movement during installation!



Never reach into the gap between machine tool,
spindle flange and functional unit.

6. Using the least possible force and speed, move the

drawtube on the machine to its front limit stop [see »Pre-
paring the machine for installation« chapter].

Содержание TOPlus mini

























































































































Результаты поиска

Содержание TOPlus mini

Отзывы:

Бренды по названию

Популярные бренды

Hainbuch TOPlus mini, Руководство по эксплуатации

Результаты поиска

Содержание TOPlus mini

Отзывы:

Бренды по названию

Популярные бренды