Hainbuch TOPlus mini Скачать руководство пользователя страница 70

Страница: 70 / 120

TOPlus mini / TOPlus premium pull-back
Installation

Order h49 7144.907-333

5. Unfasten and remove any lifting gear that may have

been required.

6. Remove the mounting aid on a vertically suspended

spindle if one was used.

7. Check the face run-out on the test surface of the spindle

flange [ideally ≤ 0.005 mm] and, if necessary, correct
carefully with a plastic hammer.

8. Screw in the drift body fixing screws on the spindle

flange and tighten to the specified tightening torque [see
»Screw tightening torques« chapter].

9. Check face run-out on the test surface of the spindle

flange [ideally ≤ 0.005 mm].

Whenever the face run-out is greater than the maximum per-
mitted value:

10. Remove the spindle flange.

11. Clean the locating face and the mating faces of the ma-

chine spindle and the spindle flange.

12. If there is a burr or slight damage, rub down the locating

face of the spindle flange and the machine spindle gen-
tly with an oil stone.

13. Reinstall the spindle flange.

14. Repeat the alignment process.

15. Repeat the face run-out test.

Содержание TOPlus mini

























































































































Результаты поиска

Содержание TOPlus mini

Отзывы:

Бренды по названию

Популярные бренды

Hainbuch TOPlus mini, Руководство по эксплуатации

Результаты поиска

Содержание TOPlus mini

Отзывы:

Бренды по названию

Популярные бренды