Hainbuch TOPlus mini Скачать руководство пользователя страница 103

Страница: 103 / 120

TOPlus mini / TOPlus premium pull-back
Removal

Order h49 7144.907-333

103

10.5 Removal of the product

Drawtube adapter

Spindle flange

B1 Fixing screws, spindle flange
B2 Transport thread spindle flange
C

Functional unit

C1  Fixing screws functional unit
C2  Screwdriver bit with tip guide
C3  Transport thread functional unit
a

Test surface face run-out spindle flange

Test surface axial run-out spindle flange

Test surface axial run-out functional unit

Test surface face run-out functional unit

Special aids needed:



Screwdriver bit with tip guide

1. As described in the »Preparing the machine for re-

moval« chapter, prepare for the following steps.

10.5.1 Removal of the functional unit

WARNING

Serious injuries caused by imbalance during in-
correct installation!



When removing the product, check that the bal-
ance marks on the spindle flange and functional
unit are still there.



If the balance marks are no longer there, remove
the product from the machine and send it to HAIN-
BUCH.

1. Attach any lifting gear that may be required.

2. If necessary, fit the mounting aid onto a vertically sus-

pended spindle.

3. Move the machine drawtube to its rear limit stop.

Содержание TOPlus mini

























































































































Результаты поиска

Содержание TOPlus mini

Отзывы:

Бренды по названию

Популярные бренды

Hainbuch TOPlus mini, Руководство по эксплуатации

Результаты поиска

Содержание TOPlus mini

Отзывы:

Бренды по названию

Популярные бренды